Motorsport Mickey Posted July 3, 2020 Report Share Posted July 3, 2020 14 minutes ago, EliTR6 said: Gonzo! Wow, haven't posted for almost a month. The tr3 is pretty much my daily driver but I've been working 6 days a week and often 12 hours a day so haven't done anything apart from drive it. The throttle sometimes sticks open at full bore. It's happened a few times on 4th. Accelerate hard and lift off the gas but it keeps pulling. Drop into neutral and the revs are bouncing off the redline. Killing the ignition then tapping the throttle before jump starting in 4th mostly cures it. The linkage doesn't seem to be fouling anything and it happened once on a 100mi run last Sunday and twice on a 80mi drive today. Do you think it's inside the carb? Could something be stopping a piston from dropping back down? Got some lithium grease for my new old wanner gun. Will grease the trunnions before a 500mi trip next week. Typical wear on the carb spindle as it exits the butterfly at either end, it gets notchy and sticks on full throttle as the spindle pushes across at full piston lift. The clue is the car starts ok when bumped after tapping the throttle, with no vacuum on the piston it drops back and the throttle spindle can relax. Mick Richards Quote Link to post Share on other sites
EliTR6 Posted July 3, 2020 Author Report Share Posted July 3, 2020 3 minutes ago, Motorsport Mickey said: Typical wear on the carb spindle as it exits the butterfly at either end, it gets notchy and sticks on full throttle as the spindle pushes across at full piston lift. The clue is the car starts ok when bumped after tapping the throttle, with no vacuum on the piston it drops back and the throttle spindle can relax. Mick Richards Thanks. Carbs are reconditioned with only a few hundred miles on them. But the quality has been very disappointing so far. I'll disconnect the linkages and see if they feel sticky on Sunday. Put new spark plugs today, drove 60mi. 1 and 3 look good but 2 is completely black. I only had 3 new plugs but checked 4 and it also looked a good colour. Quote Link to post Share on other sites
EliTR6 Posted July 3, 2020 Author Report Share Posted July 3, 2020 (edited) Car pulls like a train. Nice and smooth, definitely not running on 3 cylinders. New needles (tw) and jets. Plugs are bp6hs gapped to 32 thou with electronic ignition I found this thread but there was never an update https://www.tr-register.co.uk/forums/index.php?/topic/51110-baffled-for-reason-no1-spark-plug-running-sooty/#comment-416675 Edited July 3, 2020 by EliTR6 Quote Link to post Share on other sites
EliTR6 Posted July 3, 2020 Author Report Share Posted July 3, 2020 Just pulled plug number 2 again. The soot brushed off easily and isn't oily. Underneath the soot the colour is good, same as the others. Quote Link to post Share on other sites
EliTR6 Posted July 4, 2020 Author Report Share Posted July 4, 2020 Apologies, this thread is turning into a stream of consciousness but it helps me figure things out. When reassembling the new carbs I noticed that one of the throttle spindles had a notchy feel to it. I put it down to new tight bushings and thought the return spring would overcome any resistance. And I guess the sooty plug could be caused by a weak spark. I measured the resistance of the plug lead, got 5k ohms, same as the next lead. Quote Link to post Share on other sites
DavidBee Posted July 4, 2020 Report Share Posted July 4, 2020 1 hour ago, EliTR6 said: Apologies, this thread is turning into a stream of consciousness but it helps me figure things out. Eli, I personally like this thread. I think it's daring, interesting, a diary full of insights, ups and downs of real life, generously illustrated, no need for any apologies. I was actually wondering why there was such a gap since your last post. Now I know: you were worked off your feet. The sticking carb; could it be something to do with the cable? Quote Link to post Share on other sites
EliTR6 Posted July 4, 2020 Author Report Share Posted July 4, 2020 8 hours ago, DavidBee said: Eli, I personally like this thread. I think it's daring, interesting, a diary full of insights, ups and downs of real life, generously illustrated, no need for any apologies. I was actually wondering why there was such a gap since your last post. Now I know: you were worked off your feet. The sticking carb; could it be something to do with the cable? Thanks David! It's definitely spindle related. I've disconnected the linkage clamps and the rear carb is notchy. I'm hoping it's just the throttle linkage bar sticking. I'll take the carbs off tomorrow. Quote Link to post Share on other sites
Lebro Posted July 4, 2020 Report Share Posted July 4, 2020 I have been helping a friend re-assemble an Alpine engine, & today I assembled the twin stromburgs onto the manifold using the supplied gaskets. When I checked the throttles for syncronisation one of them had a "sticking point". on investigation the butterfly was just catching on the gasket. Trimming the hole in the gasket, using a scalpel, to be flush with the manifold hole cured the problem. Just a thought that this may be your problem ? Bob. Quote Link to post Share on other sites
John Morrison Posted July 4, 2020 Report Share Posted July 4, 2020 Eli, I too would give a 10 out of 10 for your posts, so useful and what TR'ing, with its learning curves etc., is all about. John. Quote Link to post Share on other sites
harlequin Posted July 4, 2020 Report Share Posted July 4, 2020 1 hour ago, John Morrison said: Eli, I too would give a 10 out of 10 for your posts, so useful and what TR'ing, with its learning curves etc., is all about. John. Agreed it's this sort of post and the friendly help that makes this forum so addictive George Quote Link to post Share on other sites
David Owen Posted July 5, 2020 Report Share Posted July 5, 2020 4 hours ago, harlequin said: Agreed it's this sort of post and the friendly help that makes this forum so addictive George Yes. And it gives me hope. Quote Link to post Share on other sites
EliTR6 Posted July 5, 2020 Author Report Share Posted July 5, 2020 Cheers everyone! One day I'll have to write a proper recap of everything I've learnt thanks to the forum I'm not sure if this little imperfection was to blame but the dremel made quick work of it! Also maybe I had overtightened the nuts holding the carb body onto the manifold. It was moving fine after reassembly until I tightened all the nuts. Backed them off a tad and it was better. So one side could have been putting some stress on the link rod. I'm getting everything ready for our road trip tomorrow! Still have to grease everything this afternoon. Quote Link to post Share on other sites
Ralph Whitaker Posted July 5, 2020 Report Share Posted July 5, 2020 4 hours ago, EliTR6 said: Cheers everyone! One day I'll have to write a proper recap of everything I've learnt thanks to the forum I'm not sure if this little imperfection was to blame but the dremel made quick work of it! Also maybe I had overtightened the nuts holding the carb body onto the manifold. It was moving fine after reassembly until I tightened all the nuts. Backed them off a tad and it was better. So one side could have been putting some stress on the link rod. I'm getting everything ready for our road trip tomorrow! Still have to grease everything this afternoon. You know it will be the one thing you didn`t take that breaks. It is an unwritten rule of life. Ralph. Quote Link to post Share on other sites
EliTR6 Posted July 5, 2020 Author Report Share Posted July 5, 2020 26 minutes ago, Ralph Whitaker said: You know it will be the one thing you didn`t take that breaks. It is an unwritten rule of life. Ralph. My spirit is already broken Greased p/s easy, d/s nothing would go in! It will have to do for now, leaving early tomorrow morning. Quote Link to post Share on other sites
EliTR6 Posted July 6, 2020 Author Report Share Posted July 6, 2020 Made it to our first stop! Quote Link to post Share on other sites
TwinCamJohn Posted July 6, 2020 Report Share Posted July 6, 2020 Nice collection of machinery. Quote Link to post Share on other sites
EliTR6 Posted July 6, 2020 Author Report Share Posted July 6, 2020 I've put a few photos from today on Instagram http://Road trip! #triumphtr3 https://www.instagram.com/p/CCUKGavKCGg/?igshid=13wpggdmzv73f The B&B owner is swapping out a jag v12 engine! Quote Link to post Share on other sites
Ian Vincent Posted July 6, 2020 Report Share Posted July 6, 2020 I couldn't get the link to work Eli. Rgds ian Quote Link to post Share on other sites
EliTR6 Posted July 7, 2020 Author Report Share Posted July 7, 2020 https://www.instagram.com/p/CCUKGavKCGg/?igshid=1patbcsupl5lg Hopefully this will work Quote Link to post Share on other sites
MilesA Posted July 7, 2020 Report Share Posted July 7, 2020 Neat photo of the reflection off the Speedo. Must try and replicate that! Miles Quote Link to post Share on other sites
DavidBee Posted July 7, 2020 Report Share Posted July 7, 2020 38 minutes ago, EliTR6 said: https://www.instagram.com/p/CCUKGavKCGg/?igshid=1patbcsupl5lg Hopefully this will work It does! The photo of your wife reflected in the dial is pure GENIUS!! And what's the strange (octagonal?) castle? Quote Link to post Share on other sites
EliTR6 Posted July 7, 2020 Author Report Share Posted July 7, 2020 8 hours ago, DavidBee said: It does! The photo of your wife reflected in the dial is pure GENIUS!! And what's the strange (octagonal?) castle? Gisors. Nothing of note apart from the castle ruins. We're a bit further south now, near la roche guyon and giverny. The gearbox started making a noise this afternoon, I stopped a few miles down the road and it was bone dry! Put in 800ml on 20w50 and seemed ok during the 10mi to the next hotel. Holding thumbs! Quote Link to post Share on other sites
stuart Posted July 7, 2020 Report Share Posted July 7, 2020 9 minutes ago, EliTR6 said: Gisors. Nothing of note apart from the castle ruins. We're a bit further south now, near la roche guyon and giverny. The gearbox started making a noise this afternoon, I stopped a few miles down the road and it was bone dry! Put in 800ml on 20w50 and seemed ok during the 10mi to the next hotel. Holding thumbs! If it was dry off the dipstick you might want to re-check it now and top up again. Stuart. Quote Link to post Share on other sites
EliTR6 Posted July 7, 2020 Author Report Share Posted July 7, 2020 3 minutes ago, stuart said: If it was dry off the dipstick you might want to re-check it now and top up again. Stuart. Thanks. I did when we got to the hotel. Really hard to make out the clean oil on the dipstick but the max level dimple had a drop in it. Will keep an eye on it Quote Link to post Share on other sites
EliTR6 Posted July 7, 2020 Author Report Share Posted July 7, 2020 Here's where we've been today. Bee is 7 months pregnant and isn't a fan of classic cars but handled the breakdown very well. I was a lot more worried than her. Maybe she was hoping to get a comfy modern replacement car for the trip home! https://www.instagram.com/p/CCWvdx4qCYH/?igshid=fj9lh52ncqy9 Giverny tomorrow for Monet's gardens then Château Gaillard, a 12th century castle which was built for Richard the lion heart. Only 150mi to home and I've got 4 litres of oil left, good job the engine barely uses any. Wish us luck! Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.