ChrisR-4A Posted November 21, 2015 Report Share Posted November 21, 2015 Hi Roger, why are you changing the crank, have I missed something. As its already done many miles it shouldn't be prone to breakage, but how well do you know the one you are proposing to use instead? Chris Quote Link to post Share on other sites
RogerH Posted November 21, 2015 Author Report Share Posted November 21, 2015 Hi Chris, it's madness I know. The new crank is a prototype that the SDF are putting together with Moss bringing it all together. (Thank you Fergy TRactor) Â It has been cast in India and machined in Birmingham and now needs testing. Â In theory it will be equal to what ST did in the 50's, 60's at hopefully 25% to 33%% the cost of a billet steel crank. Â I'm slightly nervous because if it goes bang it could get expensive. Â Roger Quote Link to post Share on other sites
Alec Pringle Posted November 21, 2015 Report Share Posted November 21, 2015 Roger,  if it goes bang there's probably enough here to rescue the situation . . . . as you know !  Cheers  Alec Quote Link to post Share on other sites
Revolution Posted November 22, 2015 Report Share Posted November 22, 2015 Hi Roger  Is that a saw in the background of your image number 3 ?  Looking forward to hearing what you're going to be using that for......some sort of amputation maybe?!  Cheers, Nick Quote Link to post Share on other sites
RogerH Posted November 23, 2015 Author Report Share Posted November 23, 2015 (edited) Hi Nick, indeed it is a saw. I have found in the past that getting the camshaft all the way through into the block can be awkward. So perhaps cutting the block in half may help  Roger  PS - not sure why it was there. PPS - it's not a saw. It is a saw blade that I have converted into a knife. Edited November 23, 2015 by RogerH Quote Link to post Share on other sites
RogerH Posted November 23, 2015 Author Report Share Posted November 23, 2015 Hi Folks, good news this morning. Before going too far with things I needed to make sure the new crank would fit in the block. I had a problem though - do I buy a cheap (£30) set of main bearings and if all is well then buy an expensive set (£60). Or do I buy an expensive set and panick if there are problems and the project binned.  I slept on the problem but woke up tired. So I had a think over a cuppa - bingo.  When I bought the 'other' new crank (Fergy TRactor crank) it came with main/big-end and thrust washers). So I plopped in the main bearing shells, sorted out the thrust washers and stood back and admired what I had done. I then attached the DTI and checked the end float. The Tolerance is 0.004" to 0.006" - the end float was 0.004". I couldn't make it any more - happy smile on face  This afternoon I will pop out and see what I can buy at what price. (I'm not good at haggling)  Roger Quote Link to post Share on other sites
RogerH Posted November 23, 2015 Author Report Share Posted November 23, 2015 Hi Folks, Christmas budget blown Just had to do it. I've got some nice shiny bits and pieces.  Perhaps the nicest is the Christian Marx rear oil seal. This is so gorgeous that I have decided to fit it on the front of the timing chain cover so that all can see. If I decide to fit is at the back end (always a chance) does anybody have the dimensions of the mandrel. I'm sure on diameter is the main bearing hole (without the bearing) and the other is the seal holder diameter to centralise it. But!!!!  One of the few item that has significant wear is the crank pulley hub ~75 http://www.moss-europe.co.uk/shop-by-model/triumph/tr2-4a/engine/engines-components/internal-engine-components.html To have a speedy sleeve fitted costs about £30; a new hub costs about £34 - crazy.  I toyed with the idea of rotating the liners thro' 90' and reusing the pistons etc - nice economic answer but do I need economy. I investigated buying new 86mm liners and reusing the pistons - but this is almost as expensive as new liners + new pistons. So I have plumped for new 87mm + 0.010" liners and pistons - I may have to upgrade the brakes  New standard cam. I thought about a road race cam but I considered the extra whatever it gives isn't required.  Tomorrow should be fun.  Roger Quote Link to post Share on other sites
Don H. Posted November 23, 2015 Report Share Posted November 23, 2015 Roger, I have 87mm liners and pistons in my car, and it runs strong. That's a good upgrade. It did seem to make cooling more challenging, so next you'll likely be wondering how to spend money on water pump and radiator. Â We also upgraded my cam to something falling into the fast road category. It's proven to be very driveable, and gives strong pull from 2500-4500 rpm. Here's its specification, for the record: Intake :: opens 20 degrees BTDC; closes 60 degrees ABDC Exhaust :: opens 60 degrees BBDC; closes 20 degrees ATDC Duration :: 260 degrees Cam lift :: 0.290", valve lift 0.440" Valve settings (hot) intake:: 0.012" - 0.014"; exhaust 0.014" - 0.016" (in practice, 0.014" warm for both, not necessarily hot) Quote Link to post Share on other sites
RogerH Posted November 23, 2015 Author Report Share Posted November 23, 2015 Hi Don, Looking forward to giving it a good run. Â Regarding the Christian Marx rear oil seal - I've read a few old threads and one shows the oil seal having a hole cut in the 6-o-clock position to allow adequate draining. My new seal does not mention this. I will need to ensure that the drain hole is not obscured. Â Roger Quote Link to post Share on other sites
Don H. Posted November 23, 2015 Report Share Posted November 23, 2015 Chris's has these instructions on his site as of today, Roger. I seem to recall a continuing evolution in the details. The earlier version required machining to the original metal seal ring, yet now this is supplied as new parts, yes? Â The centering tool has also evolved, I believe -- at least in the US where Joe Alexander offers Chris's kit. Â My engine has the older Rover seal on machined crank -- Chris's parts were just coming out when we did mine. One of the key things to get right is the direction the rubber lip seal faces on the crank, at least for that other style and I'd guess similarly for Chris's. There has been at least one shop here with egg on their face after complaining about junk parts when they had the Rover-Revington style seal installed backwards. Quote Link to post Share on other sites
mike3md Posted November 23, 2015 Report Share Posted November 23, 2015 Roger, Â You have a pm. Â Mike Quote Link to post Share on other sites
iain Posted November 23, 2015 Report Share Posted November 23, 2015 Roger central heating engineers use a very high temp silicon for sticking rope seals into place might be the solution to the pushrod tube issue. Pool liner ......too small,won't stretching into place,guessing?..........kettle of hot water on the beaded edge,watch your pinkies but it will stretch like you won't believe.repeat as necessary. Iain Quote Link to post Share on other sites
RogerH Posted November 23, 2015 Author Report Share Posted November 23, 2015 Hi Iain, still thinking about the tubes. Metal to metal is no good. Solder is probably too prone to problems. Swagging with some form of seal sounds the way to go but it has to be spot on. Â Still time to think more about it. Â Roger Quote Link to post Share on other sites
stuart Posted November 24, 2015 Report Share Posted November 24, 2015 Roger I have the correct Mandrel if you need it from a Marx kit. Stuart. Quote Link to post Share on other sites
RogerH Posted November 24, 2015 Author Report Share Posted November 24, 2015 Hi Stuart, I think I have a mandrel. I'm sure I made one last year or so. If I have a problem I may be on the ear 'ole  Roger Quote Link to post Share on other sites
stuart Posted November 24, 2015 Report Share Posted November 24, 2015 I have both the original style for original rear seal and the Marx one. They are different Roger. Stuart. Quote Link to post Share on other sites
RogerH Posted November 24, 2015 Author Report Share Posted November 24, 2015 Hi Stuart, I'll dig it out in a mo and give it a measure. Â Roger Quote Link to post Share on other sites
Stevecross Posted November 24, 2015 Report Share Posted November 24, 2015 Roger A bit of a jump back to the start of this thread when you mentioned rust in the nearside sill. Harks back to years ago but I was always told that cars were generally parked nearside to the kerb. Kerbs had a bigger camber back then and therefore the car sat over at an angle and accumulated water that could not escape through the horizontal drain holes. Urban myth or true? Steve Quote Link to post Share on other sites
RogerH Posted November 24, 2015 Author Report Share Posted November 24, 2015 Hi Steve, could be so as the near side is much worse than the off side. Â Roger Quote Link to post Share on other sites
stillp Posted November 24, 2015 Report Share Posted November 24, 2015 Possibly more frequent puddles on the nearside as well Steve. Â Pete Quote Link to post Share on other sites
RogerH Posted November 24, 2015 Author Report Share Posted November 24, 2015 (edited) Hi Folks, I was cleaning some bits and pieces today and found the source of one oil leak. The small hub that takes the crank pulley for the water pump etc  It never dripped directly below itself but got blown back and made other things wet.  I think a bit of JB Weld should sort it.  Roger   Edited November 24, 2015 by RogerH Quote Link to post Share on other sites
peejay4A Posted November 24, 2015 Report Share Posted November 24, 2015 (edited) Speedi-Sleeve? Edited November 24, 2015 by peejay4A Quote Link to post Share on other sites
RogerH Posted November 25, 2015 Author Report Share Posted November 25, 2015 Hi Pete, to have a speedi-sleeve fitted costs £30. A new hub costs £34 !!!!!!  Roger Quote Link to post Share on other sites
stuart Posted November 25, 2015 Report Share Posted November 25, 2015 Then fit a new hub. Stuart. Quote Link to post Share on other sites
MichaelH Posted November 25, 2015 Report Share Posted November 25, 2015 Looked at the photo and thought about the "hub" that takes the pulley for the water pump etc Are you talking about the front end of the crank or the timing chain case-or the pulley? I am lost Am interested because my engine looses oil and I can't see where? Do post a wider photo so I can see what you are talking about please Michael Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.