bazyli56i Posted February 2, 2018 Report Share Posted February 2, 2018 Hi, I have a 1966 TR4A which has a standard exhaust system with the crossbox silencer at the rear, the exhaust is steel with the exception of the crossbox silencer which is stainless steel, the y section which connects to the front manifold is cracked and I am thinking about replacing the complete system for a pheonix stainless steel one retaining the original manifold, my dillema is do i go for the crossbox or change it to the twin pipe system as i quite like the look of the twin pipe outlets, although a bit concerned about how the twin pipes are supported. Is there brackets that support the silencers or do they have to be manufactured. Cheers Quote Link to post Share on other sites
Geko Posted February 2, 2018 Report Share Posted February 2, 2018 They are supported by 2 armored rubber straps that attach to the rear cross tube. They are available from the usual suppliers or make your own. While opting for twin pipes, consider that back wind depression will send exhaust fumes into the cockpit, not a problem if you have a surrey but it is a problem if you haven't and drive with the roof down. In this case the cross box is a better choice as it sends the fumes sideways. Quote Link to post Share on other sites
brenda Posted February 2, 2018 Report Share Posted February 2, 2018 I like my twin pipes. Mike Redrose group Quote Link to post Share on other sites
stuart Posted February 2, 2018 Report Share Posted February 2, 2018 They are supported by 2 armored rubber straps that attach to the rear cross tube. They are available from the usual suppliers or make your own. While opting for twin pipes, consider that back wind depression will send exhaust fumes into the cockpit, not a problem if you have a surrey but it is a problem if you haven't and drive with the roof down. In this case the cross box is a better choice as it sends the fumes sideways. Not applicable on 4a only the 6`s suffer this due to the Kamm tail. You will find slightly less ground clearance with the twin pipes unless very careful fitting of the boxes can be achieved Stuart. Quote Link to post Share on other sites
boxofbits Posted February 2, 2018 Report Share Posted February 2, 2018 I prefer the look of the cross-box and it tucks up nicely in the rear left corner. Not the same car but I had a Peco big bore centre exhaust on my 850 Mini many years ago and it either got flattened or ripped off completely! Kevin Quote Link to post Share on other sites
ChrisR-4A Posted February 2, 2018 Report Share Posted February 2, 2018 Hi Baz, Phoenix are well made but quite a bit louder than standard systems. Too loud for us on long motorway journeys but a compromise is the TR 250 twin outlet cross box in SS. Has single inlet pile and more flow and crisper note from twin outlets Chris Quote Link to post Share on other sites
Malbaby Posted February 2, 2018 Report Share Posted February 2, 2018 I replaced the front twin pipes that connect to the exhaust manifold with a single SS pipe all the way. Cut the top mounting plate off the twin pipes and welded a 2 into one collector onto the modified plate. I run 2 mufflers, small one at the front and larger at rear with single exit pipe. If you like the look of twin exhaust pipes poking out under the rear, use a rear muffler with 2 exit pipes. Quote Link to post Share on other sites
PaulAnderson Posted February 3, 2018 Report Share Posted February 3, 2018 (edited) Mines an SS Systems twin pipe stainless exhaust. It comes with a central silencer box and then another box in each of the twin pipes. Okay system at a decent price. I have however caught the front central box twice and had to replace it once. Bought from London TR Shop. I'd thought about going for the Phoenix system but was slightly put off due to the noise concerns - don't want to wake the neighbours when coming home late. Reading old posts they used to do quieter and louder versions but no longer do. Paul Edited February 3, 2018 by PaulAnderson Quote Link to post Share on other sites
brenda Posted February 3, 2018 Report Share Posted February 3, 2018 My system is the moss Ss four branch manifold no central box and the two rear boxes. Just thinking of putting wrap on the manifold. Mike Redrose group Quote Link to post Share on other sites
bazyli56i Posted February 11, 2018 Author Report Share Posted February 11, 2018 Hi Guys, Thanks for the replies/views, I have decided to go for the pheonix twin pipe system complete with down pipe (Mike from the red rose group, the picture you sent clinched it for me) , getting fitted on Tuesday. Cheers John Quote Link to post Share on other sites
brenda Posted February 24, 2018 Report Share Posted February 24, 2018 Hi John hope you got you Phoenix twin pipe fitted,would be nice if you could put some photos on so we have a look at it, may encourage more to us to use this s type of system. Photo of the four branch I installed to my system. Mike Redrose group Quote Link to post Share on other sites
John Morrison Posted February 24, 2018 Report Share Posted February 24, 2018 Hi Mike, Apologies to all for just diverting this thread a tad, can you tell me about your CB installation, especially arial and its mount, and cablr route. Thanks John. Quote Link to post Share on other sites
PYU940F Posted February 24, 2018 Report Share Posted February 24, 2018 (edited) I have had the standard twin pipe in S/S since 1986 although the standard for a '67 car is crossbox. . I have always thought my exhaust looked good but sounded tinny and driving other 4a's with X boxes the sound is deeper and throatier. I have just bought the standard front "Y" piece to replace the front silencer to see what the difference would be. If this proves to be too noisy then I will replace the twin boxes with an X box. I think other 4a owners have done the same; is it really too loud? I like the idea of Chis's to put the phoenix TR250 X box as it has single pipe inlet so no major mods but wth the nice looking side twin exhausts. Chris, does t sound like a TR5? Simon Edited February 24, 2018 by PYU940F Quote Link to post Share on other sites
peejay4A Posted February 24, 2018 Report Share Posted February 24, 2018 (edited) I did away with the front resonator Simon and the twin pipe system isn*t too loud imo. Indeed I*ve had compliments on the sound. * = insert apostrophe here. Edited February 24, 2018 by peejay4A Quote Link to post Share on other sites
boxofbits Posted February 24, 2018 Report Share Posted February 24, 2018 I have had the standard twin pipe in S/S since 1986 although the standard for a '67 car is crossbox. . I have always thought my exhaust looked good but sounded tinny and driving other 4a's with X boxes the sound is deeper and throatier. I have just bought the standard front "Y" piece to replace the front silencer to see what the difference would be. If this proves to be too noisy then I will replace the twin boxes with an X box. I think other 4a owners have done the same; is it really too loud? I like the idea of Chis's to put the phoenix TR250 X box as it has single pipe inlet so no major mods but wth the nice looking side twin exhausts. Chris, does t sound like a TR5? Simon I use the x/box and the car is quiet to drive, but does still have a pleasant raspy exhaust note at certain RPM. It's also correct for my '67 4A car. I would normally reserve a twin exhaust for a V engine and always think it looks too over the top for an in-line 4 pot, but not everyone has the same taste I know. Kevin Quote Link to post Share on other sites
PYU940F Posted February 24, 2018 Report Share Posted February 24, 2018 Thanks for the comments. The twin pipes were standard '65 and '66. Apparently some time in '67 they switched to X box with single exit, perhaps in anticipation on the TR5 (although I think this had twin exit pipers). Will fit the non silenced Y piece and report back. Only question is do I crawl underneath and graze my knuckles and forehead, along with varying degrees of swearing or pay £50? to my local Mr. exhaust. No contest I think. Simon Quote Link to post Share on other sites
brenda Posted February 26, 2018 Report Share Posted February 26, 2018 John Morrison re CB. I have my cb fixed under the grab handle on the passenger side of the car, the cable then runs between the carpet and underlay into the boot. Then through the rubber grommet with the number plate light supply, the bracket is fixed to the bumper iron to the chassis with a additional earth to body. Mike Redrose group Quote Link to post Share on other sites
RogerH Posted February 26, 2018 Report Share Posted February 26, 2018 Hi Mike, that is how I used to attach my aerial - works a treat and no holes in the bodywork. I fitted the box to the dash top for convenience and the normal FM radio aerial to the bumper Roger Quote Link to post Share on other sites
bazyli56i Posted April 24, 2021 Author Report Share Posted April 24, 2021 Apologies Brenda/Mike Red Rose Group, was just reading through old posts and you requested photo's of the pheonix twin sports exhaust fitted and I missed your request. Quote Link to post Share on other sites
BRENDA1 Posted April 24, 2021 Report Share Posted April 24, 2021 Thank you very much better late than never, great photos I fitted new exhaust it good and informative to look back on old posts. Mike Redrose Group Quote Link to post Share on other sites
BlueTR3A-5EKT Posted April 24, 2021 Report Share Posted April 24, 2021 How loud is it with the front resonator silencer missing? Quote Link to post Share on other sites
BRENDA1 Posted April 24, 2021 Report Share Posted April 24, 2021 Mine is not that loud, nice sound going through the gears with foot down but once up to 60 it is very pleasant not loud for touring so it doesn’t get on the wife’s nerves. Mike Redrose Group Quote Link to post Share on other sites
Efuentes Posted April 24, 2021 Report Share Posted April 24, 2021 Good that this old post was rescued. I also have twin pipes in my 1966 TR4A which I also believe were standard fit in that year, and have experienced the issue that Geko mentioned: I get some exhaust smoke blow back into the cockpit when driving roof down. Not sure if this is also an issue for other exhaust configuration. It’s not a big issue if properly carbureted and once warm, but I was wondering if there is a way to avoid it, other than fitting a Surrey top or a mesh screen Quote Link to post Share on other sites
tim hunt Posted April 24, 2021 Report Share Posted April 24, 2021 For anyone bothered about original appearance the change on the 4A from twin pipes to cross box was made at CTC70000 ~ July 1966. Fifty years ago I fitted two PECO big twin rear silencers to NGP 86D, I fondly imagined people might think I had a V12 under the hood! The exhaust note was wonderful through the gears but unfortunately there was a kind of reverberation at ~ 3000rpm that was tiresome when motorway cruising. Tim Quote Link to post Share on other sites
bazyli56i Posted May 4, 2021 Author Report Share Posted May 4, 2021 BlueTR3A-5EKT the exhaust note I would say is lovely, it peaks at 2000 rpm and has a great sound especially in tunnels and in areas with high buildings either side, it quietens down after 2000 rpm to a moderate tone which is not tiresome Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.