AlanG Posted January 14, 2014 Report Share Posted January 14, 2014 Just wondered what type of jack people carried in their TR's. I don't fancy the original side jack and bottle jacks are a bit tall. So is the scissor jack the answer or maybe a racing trolley? Alan. Quote Link to post Share on other sites
RogerH Posted January 14, 2014 Report Share Posted January 14, 2014 The scissor jack is difficult when the car has a flat tyre. However an electric jack works well. Also handy to help fit the gearbox after a clutch change. Roger Quote Link to post Share on other sites
Peter Cobbold Posted January 14, 2014 Report Share Posted January 14, 2014 I've long used a scissor jack and 2" thick block of wood to drive flat tyre onto. Quote Link to post Share on other sites
John Morrison Posted January 15, 2014 Report Share Posted January 15, 2014 The correct sissor jack will go under a TR with a flat tyre. saddle is useless, weld up a frame that engages the chassis, Cut the eye off, and weld up a nut so you can use with a ratchet and extension, and chuck away the crappy handles they come with. Pictures if you want. John. Quote Link to post Share on other sites
Peter Cobbold Posted January 15, 2014 Report Share Posted January 15, 2014 The correct sissor jack will go under a TR with a flat tyre. saddle is useless, weld up a frame that engages the chassis, Cut the eye off, and weld up a nut so you can use with a ratchet and extension, and chuck away the crappy handles they come with. Pictures if you want. John. I forgot the lowered suspension on mine. Ground clearance 4 1/4 inch, less with a flat. Peter Quote Link to post Share on other sites
TorontoTim Posted January 15, 2014 Report Share Posted January 15, 2014 (edited) Ali "racing" trolley jack that has low clearance. Simple, fast, not too heavy. Plus, you can use it to do just about anything. A bit bigger than others, but not enough (in my opinion) to outweigh the huge advantages. Edited January 15, 2014 by TorontoTim Quote Link to post Share on other sites
Guest Posted January 15, 2014 Report Share Posted January 15, 2014 This: Quote Link to post Share on other sites
Lebro Posted January 15, 2014 Report Share Posted January 15, 2014 This thread got me thinking - will my hyraulic bottle jack actually be any use if I have a flat tyre ? Well having checked ground clearances, & deducted 4" for a flat tyre - the answer is NO ! I recon I needed a jack wich would go down to 4" (rear is worse than front) This is assuming that you use not the chassis to jack onto, but the bottom of the suspension - which is not as low as the chassis will be. So, Have just ordered from ebay a new 1 ton scissor jack which goes down to 85mm (3.4") That should do the trick. ) http://www.ebay.co.uk/itm/390736033622?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649#ht_2035wt_2209 Bob. Quote Link to post Share on other sites
Don H. Posted January 15, 2014 Report Share Posted January 15, 2014 This: What vehicle did that come from originally, Menno? Quote Link to post Share on other sites
Guest Posted January 15, 2014 Report Share Posted January 15, 2014 (edited) What vehicle did that come from originally, Menno? From a local motorfactors' store. Originally, it's this one, but I've altered the top end: I will dig up some more pics. As you can see on the pic of my previous posting, there's now a hole in the center of the jack. I made an U-shaped part (can't remember how it's called in English...) with a pin under the horizontal part of the U and rubber inlay. The pin fits the hole. The U shaped part fits around the chassis leg under the door! So from the bottom up: scissor jack on the ground U shaped device on top of the jack, pin located inside the center hole Whole contraption offered up under the chassis rail Lift the jack with the U shape Menno EDIT: forgot to mention: my car's jack fits under the chassis rail with a flat tyre; I used the TR's original steel wheels with the old tyres for a test. As you see, the jack is extremely low when folded. Menno Edited January 15, 2014 by Menno van Rij 2 Quote Link to post Share on other sites
Dave Larnder Posted January 16, 2014 Report Share Posted January 16, 2014 Menno Doesn´t the scissor jack go into the spare wheel well, next to the tyre or even in the upturned wheel? that way the boot is not compromised, after all you have to go into the wheel well to get the spare out anyway. I have never needed to use the original jack and spanner, so I don´t know it´s shortfall (if any), I keep it in a wooden round ring 33 mm thick, routed out to their shapes and fitted inside the spare wheel rim. That way I keep my safety triangles in there along with the spare fan belt, hoses and if on a long run like Switzerland a spare inner tube. Dave Quote Link to post Share on other sites
Badfrog Posted January 16, 2014 Report Share Posted January 16, 2014 I have a Menno-like scissors, from an old SIMCA 1000. I'm not really enthusiast as it tends to kink under load. I plan to find a Freelander scissor jack which comes in a specific pouch. Very nice. If it can raise 1.7 ton, it will do for the TR4. Matter of fact, any Land Rover SJ will do. Badfrog Quote Link to post Share on other sites
BlueTR3A-5EKT Posted January 16, 2014 Report Share Posted January 16, 2014 (edited) I have a Menno-like scissors, from an old SIMCA 1000. I'm not really enthusiast as it tends to kink under load. I plan to find a Freelander scissor jack which comes in a specific pouch. Very nice. If it can raise 1.7 ton, it will do for the TR4. Matter of fact, any Land Rover SJ will do. Badfrog But will it go under your car when the tyre is flat? The orig dark green scissor jack for TR4A-6 is a tiddly item that went very low and works OK. I have both the orig pillar jack for the TR3 and the later IRS scissor jack in the spare wheel compartment of the TR3. Along with enough 'stuff' I have now forgotten what it was for.... When I have used the orig pillar jack I have found it to be quite adequate for the task in hand. The only reservation is that the car needs to be chocked to stop it rolling when being raised. I carry two metal chocks from a Datsun Violet, which are just bent metal so nest with each other, taking little space. Those were the days when you just 'popped' to the breakers and collected the things you fancied. Peter W PS Wrap it all up in a big rag with a pair of disposable rubber gloves. You will need them all if changing a tyre and it stops it rattling. Edited January 16, 2014 by BlueTR3A-5EKT Quote Link to post Share on other sites
McMuttley Posted January 16, 2014 Report Share Posted January 16, 2014 On this, can some one remind me of the jacking points for a 3A, Tony Schreach showed me at IWE and Ive since forgotten. Thanks Quote Link to post Share on other sites
Lebro Posted January 16, 2014 Report Share Posted January 16, 2014 The original jacking points for a 2 - 3A are round holes in the floor in front of the seats. Remove rubber (or steel for early cars) blanking disc's, & locate the jack on the chassis through the hole. If you have the original jack, it's fairly obvious where to attach it, if not, go for a scissor type, & push it under the rear spring, or under the lower front spring plate. Bob. Quote Link to post Share on other sites
Don H. Posted January 16, 2014 Report Share Posted January 16, 2014 ... there's now a hole in the center of the jack. I made an U-shaped part (can't remember how it's called in English...) with a pin under the horizontal part of the U and rubber inlay. The pin fits the hole. The U shaped part fits around the chassis leg under the door! So from the bottom up... Thanks, Menno. We would probably call the piece you made a "saddle". Quote Link to post Share on other sites
Guest Posted January 16, 2014 Report Share Posted January 16, 2014 Thanks, Menno. We would probably call the piece you made a "saddle". 'saddle' will do! Menno Quote Link to post Share on other sites
AndrewMAshton Posted January 16, 2014 Report Share Posted January 16, 2014 Hello, I also carry a foot pump, I have only ever had one flat, tried the scissor jack, nigh on impossible so I pumped the tyre up, put the scissor jack underneath and completed the job, cheers, Andrew Quote Link to post Share on other sites
john.r.davies Posted January 17, 2014 Report Share Posted January 17, 2014 The Vitesse is so low (at the front, anyway, and with the tyre inflated) that even a 'racing' trolley jack is too high, so I have a pair of caravan levelling wedges. See pic. The corrugations on the tilted face allow two to lock together, making them easy to pack away, and they can double as chocks, too, using the back end. Try your local caravan or campervan dealer. John Quote Link to post Share on other sites
Rob Briggs Posted January 19, 2014 Report Share Posted January 19, 2014 For some years I've carried an inflatable jack which is fine for wheel changing. It connects to the exhaust pipe via a one-way valve and running the engine will inflate it pretty quickly. Good points - It will fit into the smallest space between the ground and the chassis. It's good for soft ground. It's very strong (the idea originally came from tank rescue) but I do use a spare rubber mat to give extra protection form the bag being punctured. Downsides - You need to be aware of the safety aspect (I usually put the spare wheel under the chassis in case of a puncture to the bag). It's a little bulky when folded. You need to expel the exhaust fumes after use or your car will stink. I don't know whether they are still available but mine has helped me out several times including the time when a wheel came off (don't ask!) and the space available for a jack was nearly zero. Rob Briggs Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.