Trevors Posted October 10, 2023 Report Share Posted October 10, 2023 My 1971 fuel injected TR6 has started cutting out when everything gets hot. My reading suggests this is a known fault caused by the fuel pump overheating and causing the fuel to evaporate. I believe this fuel pump dates to 1985. When I leave it to cool the car runs normally. I live in the North West of England . I believe this requires a specialist to sort out. Please will members point me towards someone who can do this. Many thanks Mark Quote Link to post Share on other sites
stuart Posted October 10, 2023 Report Share Posted October 10, 2023 Not necessarily, could be ignition related, does the pump make funny noises? Stuart. Quote Link to post Share on other sites
Mike C Posted October 10, 2023 Report Share Posted October 10, 2023 "started cutting out when everything gets hot"- also often caused by a blocked fuel tank vent. Quote Link to post Share on other sites
RobH Posted October 10, 2023 Report Share Posted October 10, 2023 It sounds as though this is a recent thing, which surely makes it unlikely to be due to the pump suddenly starting to overheat as it would have been doing that since day 1. Are the fuel filters clean? Have you done any diagnostic tests? e.g. when the engine stops is there still a spark at the plugs? Quote Link to post Share on other sites
Jonny TR6 Posted October 10, 2023 Report Share Posted October 10, 2023 Plenty of specialists in the North West, TRBitz in Warrington and Stuart at Montadore Motors in Birkenhead. Quote Link to post Share on other sites
Ernest Posted October 10, 2023 Report Share Posted October 10, 2023 I was having a similar problem - and thanks to a range of advice made available on this site, I fitted a new red rotor arm - And this seem to have cured the cutting out - as Stuart noted '...possible ignition-related.' So a cheap (£14.99 'Distributor Doctor') and very easy to fit. Ernest Quote Link to post Share on other sites
Jules TR6 Posted October 10, 2023 Report Share Posted October 10, 2023 (edited) …for me this ended up being a relatively new resin filled coil (resin-filled seems to be chosen for it's vibration resistance, oil-filled for cooling effect). I’ve even got stainless steel braided fuel lines over the engine - and they cause no issues. I put an old oil filled coil in, and bingo, no problem once hot. / The fuel pump issue you may have been reading about could be related to the old Lucas pump, the newer Bosch pumps should be ok, and I wouldn't point my finger at it immediately - especially if you can hear it pumping after the engine cuts out. Just bung another coil in (easy DIY job), oil filled, and see what happens. Edited October 11, 2023 by Jules TR6 Quote Link to post Share on other sites
Andy Moltu Posted October 10, 2023 Report Share Posted October 10, 2023 Back in the day, when the PI cars were current, an awful lot of problems were caused or compounded by the assumption that any and every rough running of a 6 was the result of a PI problem. The result was a lot of Lucas PI systems meddled with unnecessarily when the fault was elsewhere, just making it so much harder to identify the real cause. Unless the cutting out coincides with a sudden change of the tone of the fuel pump, the sensible starting point is with the ignition system. Quote Link to post Share on other sites
Trevors Posted October 13, 2023 Author Report Share Posted October 13, 2023 Many thanks to you all for all that input. I'll take this forward and see if I can cure it once and for all. Quote Link to post Share on other sites
john.r.davies Posted October 13, 2023 Report Share Posted October 13, 2023 No one has mentioned the fuel line coil around the pump, that has been a popular way to keep the pump cool. Rimmer's even sell one! https://www.google.com/search?client=ms-android-vf-gb-revc&sca_esv=573265106&sxsrf=AM9HkKm5PdsV8G_0O0TEMWDor4CeOqSe4g:1697226316418&q=lucas+pi+fuel+pump+coil&tbm=isch&source=lnms&sa=X&ved=2ahUKEwiZ08Xd5POBAxX-hf0HHXUFD7sQ0pQJegQICRAB&biw=360&bih=628&dpr=2#imgrc=l6GIveIadFaIUM Quote Link to post Share on other sites
Mike C Posted October 13, 2023 Report Share Posted October 13, 2023 1 hour ago, john.r.davies said: No one has mentioned the fuel line coil around the pump, that has been a popular way to keep the pump cool. Rimmer's even sell one! https://www.google.com/search?client=ms-android-vf-gb-revc&sca_esv=573265106&sxsrf=AM9HkKm5PdsV8G_0O0TEMWDor4CeOqSe4g:1697226316418&q=lucas+pi+fuel+pump+coil&tbm=isch&source=lnms&sa=X&ved=2ahUKEwiZ08Xd5POBAxX-hf0HHXUFD7sQ0pQJegQICRAB&biw=360&bih=628&dpr=2#imgrc=l6GIveIadFaIUM As far as I can see, the coils just put the pump casing heat back into the fuel, exacerbating any fuel vapourization problem. Quote Link to post Share on other sites
john.r.davies Posted October 14, 2023 Report Share Posted October 14, 2023 Yes, Mike C, but it depends on how you plumb it. If the coil is in the return line then heat gained is diluted in the mass of fuel in the tank. John Quote Link to post Share on other sites
Mike C Posted October 14, 2023 Report Share Posted October 14, 2023 48 minutes ago, john.r.davies said: Yes, Mike C, but it depends on how you plumb it. If the coil is in the return line then heat gained is diluted in the mass of fuel in the tank. John Doesn't matter, the pump heat still ends up in the petrol- that's why car manufacturer's use fuel/air heat exchangers to solve this problem. Quote Link to post Share on other sites
roy53 Posted October 14, 2023 Report Share Posted October 14, 2023 1 hour ago, john.r.davies said: Yes, Mike C, but it depends on how you plumb it. If the coil is in the return line then heat gained is diluted in the mass of fuel in the tank. John Yes every little helps Quote Link to post Share on other sites
Waldi Posted October 14, 2023 Report Share Posted October 14, 2023 I never believed the effectiveness of the coil around the pump-motor: Is it to cool the petrol in the coil with the motor? No. To cool the motor with the coil? No To cool the petrol in the coil by the surrounding air? Yes, maybe, but just a tiny bit. It is a poor location if that was the intend. Modern fuel coolers, as discussed on here are far more efficient in cooling fuel. Waldi Quote Link to post Share on other sites
john.r.davies Posted October 14, 2023 Report Share Posted October 14, 2023 My TRansit has one as standard. Quote Link to post Share on other sites
Mike C Posted October 14, 2023 Report Share Posted October 14, 2023 Same with my Isuzu Dmax 4WD. Quote Link to post Share on other sites
michaelfinnis Posted October 15, 2023 Report Share Posted October 15, 2023 8 hours ago, Waldi said: I never believed the effectiveness of the coil around the pump-motor: Is it to cool the petrol in the coil with the motor? No. To cool the motor with the coil? No To cool the petrol in the coil by the surrounding air? Yes, maybe, but just a tiny bit. It is a poor location if that was the intend. Modern fuel coolers, as discussed on here are far more efficient in cooling fuel. Waldi It’s not fuel cooler, it’s intended to cool the motor, using petrol as the cooling medium. The temperature of the petrol through the coil is raised, but is then returned to the tank where the larger volume of petrol acts as a heat sink. Quote Link to post Share on other sites
Mike C Posted October 15, 2023 Report Share Posted October 15, 2023 33 minutes ago, michaelfinnis said: It’s not fuel cooler, it’s intended to cool the motor, using petrol as the cooling medium. The temperature of the petrol through the coil is raised, but is then returned to the tank where the larger volume of petrol acts as a heat sink. With fuel vapourization the problem is not caused by a hot pump motor, it's caused by fuel boiling when its temperature dependent vapour pressure exceeds the operating pressure in the fuel piping. The piping with the lowest operating pressure is the pump suction and the fuel vapourises in this first, and the Bosch pump stops pumping as it can't pump vapour. Feed the pump cold petrol and fuel vapourisation won't occur. Quote Link to post Share on other sites
Waldi Posted October 15, 2023 Report Share Posted October 15, 2023 Hi Michael, That’s why I cannot imagine it was designed to cool the motor: In that case it was intended to fix a motor temperature problem that exacerbated the fuel vaporisation, leading to cavitation. Waldi Quote Link to post Share on other sites
roy53 Posted October 15, 2023 Report Share Posted October 15, 2023 5 hours ago, michaelfinnis said: It’s not fuel cooler, it’s intended to cool the motor, using petrol as the cooling medium. The temperature of the petrol through the coil is raised, but is then returned to the tank where the larger volume of petrol acts as a heat sink. +1 Quote Link to post Share on other sites
Andy Moltu Posted October 15, 2023 Report Share Posted October 15, 2023 4 hours ago, Waldi said: Hi Michael, That’s why I cannot imagine it was designed to cool the motor: In that case it was intended to fix a motor temperature problem that exacerbated the fuel vaporisation, leading to cavitation. Waldi I'm not sure much thought went into the design of the cooling coil. It wraps around the motor case above the pump so only indirectly cools the pump if at all. Worse still, it heats the fuel so that it compounds the problem. So, when the tank is low and the filling pressure of the pump is low, the fuel is at it's warmest and thus more likely vaporise in the pump. If the fuel from the coil subsequently passed through a cooler before being returned to the tank it might have been better but the siting of the pump and PRV makes that impractical. A number of modern vehicles do use coolers on their return flow from the fuel rail. Of course that fuel has been heated in the engine bay heat and not just by the pump. Is that to reduce the risk of vaporising or simply to restrict the expansion of the fuel affecting the mixture and emissions? Quote Link to post Share on other sites
john.r.davies Posted October 15, 2023 Report Share Posted October 15, 2023 I thought to investigate and educate myself a little more about this. It's complex, as petrol is a mixture of compounds, all with different vapour pressures, but Lucas Pi operates at 105psi, when the "Reid Vapor Pressure" (measured at 38C) of the mixture is between 1 and 20psi. The temperature at which a liquid will boil is defined as the temperature at which it's vapour pressure exceeds the ambient pressure, usually atmospheric. That Boiling Point of the mixture that is petrol is 65 to 90C. This graph indicates that too, but a Lucas Pi system, after the pump, is regulated to 105psi, when atmospheric is about 15psi. So the pump and post pump piping will need to be hotter than before the fuel boils, and produces bubbles of vapour in the system. 60C is more than 'hand hot' and 90 is scalding hot! Is "fuel vapourization" a false fear? Next to engine, after a run and sitting in the sun, fuel lines in the engine bay might get that hot, but while running? I'll be grateful for comments from others who know more than me! John Quote Link to post Share on other sites
Jules TR6 Posted October 15, 2023 Report Share Posted October 15, 2023 The stainless-steel braided fuel lines that are often fitted between the MU and the injectors (as a stronger 'upgrade' to the original nylon lines) have been deemed a poor choice - due to conducting the heat of the engine, over which they pass. I pointed my finger at them while have worsening misfires, then I made sure they weren't actually touching the top of the engine, and that they weren't all 'clamped' tight to each other. I'm not sure this helped much, but worth doing. My misfire finally was identified as the new coil - not firing when hot. Since that was was replaced, I've had no issues with misfire or 'hot fuel lines'. I did buy some Design Engineering foil wrap, that I intended to place gently around the fuel lines directly above the engine, but wasn't required. I think coils getting too hot are a bigger issue than fuel lines. Some though put a lower temp thermostat in to run the engine slightly cooler, I've not needed that either, but is an option. Quote Link to post Share on other sites
john.r.davies Posted October 15, 2023 Report Share Posted October 15, 2023 Jules, Blaming braided injector lines is almost certainly misplaced! Because; 1/ they are silvery, the worst finish to pick up heat. Standard lines by contrast are Matt black, the best finish for the same purpose! 2/ they have a small diameter, and so surface area. Heat transfer is directly connected to heat pick up, or loss. If you have central heating at home with 10mm pipes, or microbores, you will notice they are fitted without insulation - adding that increases the surface area and so heat loss! John Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.