james christie Posted March 10 Report Share Posted March 10 Although I use my 3A throughout the year, thanks to an early spring here, I have been out with my 3A quite a lot this week with the tonneau cover closed on the passenger side and sidescreens in situ (they will be replaced by the wind wings in a few weeks) Even after some 54 years of sidescreen cars, I’ve not yet figured out how to reconcile driving with sidescreens and tonneau cover. In my case I just let it hang down unsecured inside the door and hope for the best, which doesn’t stop the drips and doesn’t help the state of the tonneau either. How do you folks fix the tonneau around the top of the door? james Quote Link to post Share on other sites
Drewmotty Posted March 10 Report Share Posted March 10 (edited) I do the same as you. The only other option would be to slit the tonneau to take the sidescreen mounts. Edited March 10 by Drewmotty Quote Link to post Share on other sites
BlueTR3A-5EKT Posted March 10 Report Share Posted March 10 (edited) Hi James, When I fit tonneau with sidescreens I have the passenger side tonneau fitted to the pegs on the scuttle dash top and the 2nd or upper 1/4 panel peg, not the one down by the B post. Lift the tonneau before you close the door forming a V shaped channel front to rear, This catches rain that runs to the side and lets it drip out the channel on the 1/4 panel area. On the half height sidescreens I can do the first method or as I have now fitted pegs secure it to the outside of the sidescreen There is also the technique known to myself and KW as the ‘Davis Fold’. This gets the tonneau neatly folded and set behind the seats. It is good for 100 mph without billowing I am reliably told. As can be seen my tonneau is a later type with gussets( ooo err Matron) These do allow an easier movement of the seat belt. The other benefit is that the hood can be up and the tonneau on. You attach the two centre fasteners at the back of the tonneau to the car after erecting the frame but before fitting the soft top. John Davis took this trick one further to have a tonneau that fitted under the hard top when no sidescreens are fitted ( horrid things in traffic as the inside of the car becomes a sauna.). John used to drive VYP88 his primrose yellow 3A all seasons. The car is still with him but undergoing repairs. Here are photos of my old blue banger and the tonneau fit and fold methods I use. First 3 are the Davis Fold which works for both full and half tonneau use. Edited March 10 by BlueTR3A-5EKT Quote Link to post Share on other sites
Lebro Posted March 10 Report Share Posted March 10 Of course the proper answer is to wear something warmer, & not fit the side screens. Bob Quote Link to post Share on other sites
BlueTR3A-5EKT Posted March 10 Report Share Posted March 10 6 minutes ago, Lebro said: Of course the proper answer is to wear something warmer, & not fit the side screens. Bob ‘Oods is for poofs….and MG owners As heard at a London Group meeting, directed at a new owner asking about where to buy a soft top. Quote Link to post Share on other sites
Ralph Whitaker Posted March 11 Report Share Posted March 11 12 hours ago, james christie said: Although I use my 3A throughout the year, thanks to an early spring here, I have been out with my 3A quite a lot this week with the tonneau cover closed on the passenger side and sidescreens in situ (they will be replaced by the wind wings in a few weeks) Even after some 54 years of sidescreen cars, I’ve not yet figured out how to reconcile driving with sidescreens and tonneau cover. In my case I just let it hang down unsecured inside the door and hope for the best, which doesn’t stop the drips and doesn’t help the state of the tonneau either. How do you folks fix the tonneau around the top of the door? james In the early part of the year when still a bit chilly on a morning I like to run with the sidescreens on and the tonneau over the passenger side, so I just let the tonneau flap hang down inside the door. I find then that with the heater on blowing to the passenger side so as not to cook my leg, the warm air gets drawn up around me on it`s way out of the car and it is really quite cosy. The main problem I have with the tonneau is that the open edge where the zip runs flaps quite alarmingly and puts a lot of strain on the centre peg on the dash board. I think TR4s had a strap to the tunnel to stop the flapping and I am thinking of doing something similar. Ralph Quote Link to post Share on other sites
Keith Wigglesworth Posted March 11 Report Share Posted March 11 (edited) As above. +1 for Peter’s method. Keith Edited March 11 by Keith Wigglesworth Quote Link to post Share on other sites
John McCormack Posted March 11 Report Share Posted March 11 12 hours ago, BlueTR3A-5EKT said: Hi James, When I fit tonneau with sidescreens I have the passenger side tonneau fitted to the pegs on the scuttle dash top and the 2nd or upper 1/4 panel peg, not the one down by the B post. Lift the tonneau before you close the door forming a V shaped channel front to rear, This catches rain that runs to the side and lets it drip out the channel on the 1/4 panel area. On the half height sidescreens I can do the first method or as I have now fitted pegs secure it to the outside of the sidescreen There is also the technique known to myself and KW as the ‘Davis Fold’. This gets the tonneau neatly folded and set behind the seats. It is good for 100 mph without billowing I am reliably told. As can be seen my tonneau is a later type with gussets( ooo err Matron) These do allow an easier movement of the seat belt. The other benefit is that the hood can be up and the tonneau on. You attach the two centre fasteners at the back of the tonneau to the car after erecting the frame but before fitting the soft top. John Davis took this trick one further to have a tonneau that fitted under the hard top when no sidescreens are fitted ( horrid things in traffic as the inside of the car becomes a sauna.). John used to drive VYP88 his primrose yellow 3A all seasons. The car is still with him but undergoing repairs. Here are photos of my old blue banger and the tonneau fit and fold methods I use. First 3 are the Davis Fold which works for both full and half tonneau use. Same. Quote Link to post Share on other sites
stuart Posted March 11 Report Share Posted March 11 4 hours ago, Ralph Whitaker said: The main problem I have with the tonneau is that the open edge where the zip runs flaps quite alarmingly and puts a lot of strain on the centre peg on the dash board. I think TR4s had a strap to the tunnel to stop the flapping and I am thinking of doing something similar. Ralph No reason that you couldnt fit one to your tonneau, and fit a stud to the tunnel. Stuart. Quote Link to post Share on other sites
David Arrowsmith Posted March 15 Report Share Posted March 15 I fitted a pair of these wind deflectors (cheap off eBay - other sellers available) and they are very good at what they do too! Quote Link to post Share on other sites
Cleo's Dad Posted March 15 Report Share Posted March 15 Along the same sort of theme, I have made a pair of vinyl clip on side screens that I call my Cissy Flaps. not very pretty but very cheap and effective and actually keep a lot of wind and rain out of the cockpit, very good in cold weather! You can roll them up and chuck them behind the seat. Clive Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.