iani Posted December 11, 2019 Report Share Posted December 11, 2019 I'm using NGK Iridium BPR6EIX plugs but I've had some trouble with them fouling, what are others using? Quote Link to post Share on other sites
Nigel Triumph Posted December 11, 2019 Report Share Posted December 11, 2019 I can't see why fitting EFi would change the required heat range for the spark plugs, but those with more experienced may know better. So I would go for standard plugs, or better still a multi-electrode alternative like NGK BUR6ET or Bosch WR78. The multi-electrode plugs give easier starting, smoother idle and better pick up with electronic ignition, so guess they would do the same with EFi. Nigel Quote Link to post Share on other sites
Mike C Posted December 11, 2019 Report Share Posted December 11, 2019 (edited) I'm extremely satisfied with my NGK BUR6ET's -but I have standard PI. I installed them because I was getting extreme carbon fouling on the BP6ES's on short runs . They fixed the problem Edited December 11, 2019 by Mike C Note on fouling added. Quote Link to post Share on other sites
Nigel Triumph Posted December 11, 2019 Report Share Posted December 11, 2019 Over on the TSSC forum, Nick Jones recently reported that Bosch multi-electrode plugs reduced fouling on an EFi Triumph 2 litre engine. Could be just what you need? Nigel Quote Link to post Share on other sites
PodOne Posted December 11, 2019 Report Share Posted December 11, 2019 Multi electrode plugs IMO are a sales gimmick and never been convinced that they give any performance advantage other than perhaps longer life even in forced induction engines. Rather its the energy of the spark delivered to the tip in the first place. This is perhaps where Iridium tips are better as the tips erode more slowly to maintain the gap longer along with a constant spark output. I'd think about going down the COP route have a look here https://www.efi-parts.co.uk/index.php?categoryID=80 for the ultimate in spark production and is what I'd do if going EFI. I've used this company a lot in the past with excellent service with regard to both parts and rolling road set up. Andy Quote Link to post Share on other sites
KiwiTR6 Posted December 11, 2019 Report Share Posted December 11, 2019 1 hour ago, Mike C said: I'm extremely satisfied with my NGK BUR6ET's -but I have standard PI. I installed them because I was getting extreme carbon fouling on the BP6ES's on short runs . They fixed the problem +1 with the rocker cover breather disconnected from the plenum to prevent oil fouling of the rear plugs. Standard PI and distributor ignition. Quote Link to post Share on other sites
harrytr5 Posted December 12, 2019 Report Share Posted December 12, 2019 What ever you use make sure they are resistor plugs or you will have electrical problems upsetting the ECU and components. Regards Harry TR5 Nutter Quote Link to post Share on other sites
TRTOM2498PI Posted December 12, 2019 Report Share Posted December 12, 2019 Hi Iain, I had my EFI map refined some time ago, by a company called Norris Motorsport, next door to Peter Burgess actually. Karl Norris advised to put NGK BKR 7EIX in mine. This is what I now use, and I have the same set-up as you. I have done at least 15k miles on these plugs in the last two years, with no issues whatsoever. They are not expensive either. Cheers. Quote Link to post Share on other sites
iani Posted December 12, 2019 Author Report Share Posted December 12, 2019 Thanks chaps, I have ordered some BUR6ET and I’ll see how it goes with them. Quote Link to post Share on other sites
jerrytr5 Posted December 14, 2019 Report Share Posted December 14, 2019 (edited) I use NGK BR7ES in mine. As Harry says, resistor plugs and leads are required to avoid ECU interferance. I had a very irritating intermittent misfire caused by using the wrong type of lead. Jerry Edited December 14, 2019 by jerrytr5 Quote Link to post Share on other sites
iani Posted December 14, 2019 Author Report Share Posted December 14, 2019 My issue appears to not be plug related, I am getting a very strong spark out of the coil pack, I swapped the plug for a new one and was still having issues, on checking the six way connector I have between the Vauxhall V6 injector loom I have and the Emerald loom, I found moisture around the pins. In my efforts to dry this out, the wire corresponding to the problematic plug has pulled out, suggesting the connection was weak. The combination of the weak connection and the moisture is hopefully the cause of my issues. Unfortunately I can't get a new pin to click in the body, I have a new connector on order so hopefully test it soon. Quote Link to post Share on other sites
harrytr5 Posted December 14, 2019 Report Share Posted December 14, 2019 On the issue of Spark plug leads you must have the right ones for waisted spark connectors. I of course had the wrong ones which were problematic and caused a misfire a few years down the line. I asked Emerald to supply the correct leads and they now do so (will save a lot of grief in the future) . I had mine made up elsewhere and tested by Emerald but now as they make them I would order from them only. Regards Harry TR5 Nutter Quote Link to post Share on other sites
iani Posted December 14, 2019 Author Report Share Posted December 14, 2019 (edited) 1 hour ago, harrytr5 said: On the issue of Spark plug leads you must have the right ones for waisted spark connectors. I of course had the wrong ones which were problematic and caused a misfire a few years down the line. I asked Emerald to supply the correct leads and they now do so (will save a lot of grief in the future) . I had mine made up elsewhere and tested by Emerald but now as they make them I would order from them only. Regards Harry TR5 Nutter My plugs are a custom set made by Magnecor Harry, supplied by Racestorations and are what they use on EFI conversions, the issue appears to have been some liquid (petrol residue) in a connector, I have a new one arriving tomorrow and I'll remake the joint. Ignore the numbering on the leads, this was as supplied and was cobblers! Edited December 14, 2019 by iani Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.