Steve Thomas Posted December 12, 2020 Report Share Posted December 12, 2020 I have a RHD TR6, the trunnions being 1 x left hand thread / 1 x right hand thread, I have stripped the car now need to know which side of the car they fit please. Can anyone help? Quote Link to post Share on other sites
JochemsTR Posted December 13, 2020 Report Share Posted December 13, 2020 Try this: " The right hand trunnion and vertical link is right hand threaded (like a normal bolt), the left hand trunnion is left hand threaded (reversed threaded). When properly installed on the car, each trunnion will move up on the vertical link when rotated toward the front of the car. " Quote Link to post Share on other sites
RogerH Posted December 13, 2020 Report Share Posted December 13, 2020 Hi Steve, the RH thread fits on the offside of the car(RHD) . The LH thread is on the nearside of the car(RHD). Roger Quote Link to post Share on other sites
c.hydes Posted December 13, 2020 Report Share Posted December 13, 2020 I don`t want to start the "oil" or "grease" debate again, but whilst we are talking trunnions.......... I have my car up on blocks at present and thought about topping up the trunnions. I was then reminded that years ago I "blew" the bottom caps off whilst refilling and had to epoxy them back in, they have been fine since. So what's the secret to refill without over-pressurizing, and where do you look to see when its full? Thanks, Colin. Quote Link to post Share on other sites
Z320 Posted December 13, 2020 Report Share Posted December 13, 2020 (edited) My thoughts: RH thread on the right side and LH thread on the left side is "commonly" correct and means: turning the steering wheel lowers one side of the car and lifts the other the same moment - each side only a minimum! This in my opinion is not because of driving issues but because of the forces on the steering wheel. With a RH thread on both sides the forces on the steering wheel would be lower turning to the right and obviously stronger turning to the left side. I expect it makes no difference at all to change LH and RH trunnion as long you use one RH on one side and one LH on the other. Ciao, Marco Edited December 13, 2020 by Z320 Quote Link to post Share on other sites
RogerH Posted December 13, 2020 Report Share Posted December 13, 2020 18 minutes ago, c.hydes said: I don`t want to start the "oil" or "grease" debate again, but whilst we are talking trunnions.......... I have my car up on blocks at present and thought about topping up the trunnions. I was then reminded that years ago I "blew" the bottom caps off whilst refilling and had to epoxy them back in, they have been fine since. So what's the secret to refill without over-pressurizing, and where do you look to see when its full? Thanks, Colin. Hi Colin, when you pump the grease in there will be a slight pressure increase to get it through the grease paths. If the grease path is blocked with old grease then you may over pressurise something (as you previously did) In this case you need to disassemble the trunnion and clean out the old grease. Normally if you grease every year the new grease will force the old grease out of the top of the trunnion.- yoou will see this coming out from under the upper seal. Be careful not to get it on the brake disc. Roger Quote Link to post Share on other sites
Z320 Posted December 13, 2020 Report Share Posted December 13, 2020 (edited) He heared some (in my opinion) funny rules about what to oil and what to grease... My rule is very simple: oil is the best, but if you can't guarantee the oil says in you use grease. Examples: In the old days of motoring they used grease in gearboxes, with better seals oil was common. Why do we use grease in wheel bearings and not oil? My trunnions are sealed so I use oil but grease would also do the job. This is no reason for any further discussion. Ciao, Marco Edited December 13, 2020 by Z320 Quote Link to post Share on other sites
c.hydes Posted December 13, 2020 Report Share Posted December 13, 2020 22 minutes ago, RogerH said: Hi Colin, when you pump the grease in there will be a slight pressure increase to get it through the grease paths. If the grease path is blocked with old grease then you may over pressurise something (as you previously did) In this case you need to disassemble the trunnion and clean out the old grease. Normally if you grease every year the new grease will force the old grease out of the top of the trunnion.- yoou will see this coming out from under the upper seal. Be careful not to get it on the brake disc. Roger Ummmmm, thanks Roger, sounds like a big job. I`ll study the brown bible to see what's involved? Cheers Colin. Quote Link to post Share on other sites
Z320 Posted December 13, 2020 Report Share Posted December 13, 2020 (edited) Edit: the lh/rh thread doesn't matter, but the vertical link from the 4A to the 6 is angled backwards, so the trunnions are not interchangeable. There is only one way they fits. Edited December 13, 2020 by Z320 Quote Link to post Share on other sites
Charlie D Posted December 13, 2020 Report Share Posted December 13, 2020 6 hours ago, c.hydes said: ...years ago I "blew" the bottom caps off whilst refilling... To seal the bottom disc in place you can run a bead of solder around the joint with the the trunion. Problem with a used trunion is that it needs to be cleaned of all old oil/grease otherwise the solder won't flow. Even if it looks clean you may find that as you heat it there will be some oil that seeps through the joint. But it's worth a try. Charlie Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.