mjdearing Posted February 3, 2018 Report Share Posted February 3, 2018 Morning chaps, garage warmed up and ready to start floors/cills inner and outer on a Tr3 then realised I have never done this before on a tr with the body still in position and dont want to remove body if possible as im on a time scale looking at the floors it looks like a juggling act ,I can see bottom of A+B post will be in the way and I think they might need to be chopped off then reworked when floors are In so anybody done it or even got any words of wisdom before I get into it, iv got plenty to strip out before I get the grinder spinning later today. Cheers chaps Martin Quote Link to post Share on other sites
ijonsson Posted February 3, 2018 Report Share Posted February 3, 2018 A lot to cut, including A and B posts, in some parts maybe use a special spot weld drill bit, but first of all I would weld in some supports (could be screwed in the hinges nuts in the A post) between A and B posts. You need to separate the body from e the frame at least so much that you can get the consoles attached to the sill free from the frame. It's not just A and B posts that have to go, you need to cut the quarter panel and the rear inner wing as well as the bulkhead where you can find all kinds of interesting rot. Quote Link to post Share on other sites
MJF Posted February 3, 2018 Report Share Posted February 3, 2018 Hi Martin, A while back Stuart provided a really good description for the whole process, which is what I will be following when I attempt mine sometime later this year. To find, do a search on this forum for “Replacing an inner sill without removing the body”. http://www.tr-register.co.uk/forums/index.php?/topic/37164-replacing-an-inner-sill-without-removing-the-body/?hl=%2Breplacing+%2Binner+%2Bsill+%2Bwithout+%2Bremoving+%2Bbody Martin Quote Link to post Share on other sites
stuart Posted February 3, 2018 Report Share Posted February 3, 2018 Hi Martin, A while back Stuart provided a really good description for the whole process, which is what I will be following when I attempt mine sometime later this year. To find, do a search on this forum for “Replacing an inner sill without removing the body”. http://www.tr-register.co.uk/forums/index.php?/topic/37164-replacing-an-inner-sill-without-removing-the-body/?hl=%2Breplacing+%2Binner+%2Bsill+%2Bwithout+%2Bremoving+%2Bbody Martin Thanks Martin, saves me writing it out again! Stuart. Quote Link to post Share on other sites
mjdearing Posted February 3, 2018 Author Report Share Posted February 3, 2018 Cheers chaps, well a bit more than I had envisaged ,that write up Stewart is brill and thanks MJF for the link, Inge them kick panels have gone quite badly thanks for photo's luckily this is a black plate California car so not rotten out but both sill have been scraped/flatened,probably curb damaged and the floors are peppered and thin. Hi Stewart do you know of any better sills than the ones from moss etc ones with a curve would be nice or is it lead time. Ta Martin Quote Link to post Share on other sites
ijonsson Posted February 3, 2018 Report Share Posted February 3, 2018 (edited) If you need a sill I have a brand new left over. RH inner from Moss ( item no 900391). Really nice price, PM me if interested. Edited February 3, 2018 by ijonsson Quote Link to post Share on other sites
stuart Posted February 3, 2018 Report Share Posted February 3, 2018 Cheers chaps, well a bit more than I had envisaged ,that write up Stewart is brill and thanks MJF for the link, Inge them kick panels have gone quite badly thanks for photo's luckily this is a black plate California car so not rotten out but both sill have been scraped/flatened,probably curb damaged and the floors are peppered and thin. Hi Stewart do you know of any better sills than the ones from moss etc ones with a curve would be nice or is it lead time. Ta Martin Unfortunately all the sills are the same, also you will find the cut in on the step where the front corner of the door goes into when you open it isnt the right shape so needs altering. You will see what I mean when you have it in your hand. Stuart. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.