[New Rivets on Rear of Hood]

If l remember it was a while back l used the bit that unscrews from the top of a spark plug

Rob

[Gear box cover]

Thanks good idea

Rob

[Gear box cover]

Thanks Kevin l will have a look on there web site 

[Gear box cover]

Hi are the plastic or fibreglass replacement gear box covers a good fit or is there a lot of messing about

Rob

[Radiator Cowl.]

Hi what do these stays do is there any point having them on

Rob

[ECU help]

Thanks to everyone l will check out all your surgestions any more will be apricated

Rob

[ECU help]

Hi it is a new install l have a TPS on the single thottle body it’s been to emerald twice it seems ok if l just rev it but it seems to be when it’s under load l have connected the hose from the servo to where the air bleed was not sure about the idle speed controller will have to look into that

Rob

[ECU help]

Fitted emerald Ecu pressure regulator , crank sensor, air and coolant temp sensor ,coil pack, Lambo sensor used original thottle bodies with butterflies removed and single thottle body on end of air manifold problem l am having is at about 1500 revs it’s like l have kangaroo petrol anyone had this problem or anyone know how to fix it

Rob

[Ecu help]

Thanks for help have now fitted 8m return pipe not solved problem yet

rob

 

[Ecu help]

Hi fitted Ecu having problems setting it up I have put the fuel pressure gauge in engine bay so petrol comes from the fuel tank though filter ,fuel pump ,filter then though fuel rail to pressure gauge then back to tank though the old fuel return pipe my question is is the old fuel return pipe big enough 

thanks Robin

[Pressure regulator]

Thanks Jochem 

[Pressure regulator]

Hi this might seem a silly question but am fitting a Ecu and have put a pressure regulator in the engine bay does the fuel go though the regulator then to the fuel rail or the other way round

Rob

[Air temp sensor]

Thanks Rob

[Air temp sensor]

Hi am putting a emerald Ecu on my 6 and have put a single thottle body on the end of the air tube which side of the thottle body should the air temp sensor be or don’t it matter

thanks Rob

[Trigger wheel]

Thanks have now sorted it

Rob

[Trigger wheel]

Hi again got a trigger wheel put it on the back of the damper but it catches timing case how do I get over this problem

thanks Rob

[Bosch Fuel injectors]

Thanks for the picture but have now removed some material off the thottle bodies should .be ok now

thanks again Rob

[Bosch Fuel injectors]

Found some injectors on eBay from a 2.5 bmw will have to drill out thottle bodies as advised by Brent on earlier post but it looks like the fuel rail will catch the thottle bodies has anyone had this problem before

Rob

[Trigger wheel]

Hi Mark thanks good picture been on emerald site will find out what size I need and order one thanks again for your help

Rob

[Trigger wheel]

Hi it’s me again now to sort out the trigger wheel where I can get one also has anyone who has fitted one got any pictures 

Rob

[Bosch Fuel injectors]

Thanks for all your help found some on eBay 

Rob

[Bosch Fuel injectors]

Would injectors from a jag xj6 3.6 be ok or would they be to much 

Rob

[Bosch Fuel injectors]

Hi Brent

Thanks for your reply was hoping to be able to get injectors to fit straight into my thottle bodies but it looks like I will have to go down the root of opening up the holes in my thottle bodies thanks once again for your help 

Rob

[Bosch Fuel injectors]

Hi hope someone can help I am going down the root of fitting Ecu I am going to use my original thottle body’s and need to no what Bosch injectors to use part number would be good 

thanks Rob

[Electric fan]

Thanks l will have a look around