BruceA
-
Content Count
19 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Posts posted by BruceA
-
-
When I got the car stripped of paint it revealed this little lot in the rear wing, it appears to be in the shape of a gun and there was a little light fitted behind it (theres some strange folk accross the pond) anyway my original plan was to fill them with lead but as soon as I put a blowtorch near it the panel started throwing shapes and I chickened out and I reckon with that number of holes it will distort if I weld it. Any idea's greatfully recieved?
-
I inadvertently gave it a whack while getting the motor apart the shaft will clean up but I think the nuts probably toast, Peter I've sent you a PM
Cheers
Bruce
-
Hi All
Anyone know the thread size/type for the nut/shaft on the end of a Tr4 starter motor that secures the bendix gear?
Cheers
Bruce
-
Hi All
So I've got repair sections on my lower front wings coupled with some ill fitting replacement sills and theres a hefty gap do I add lead to the sills or do I attempt to reduce the metal in the repair section, the position of the holes at the base of the wing isn't helping either?
Cheers
Bruce
-
Hi Peter
Thanks that now makes perfect sense, It was the use of the word shim that confused me they are big enough to fit over the wishbone and lock washer and the seals are 5/16" so I'll put them in.
Cheers
Bruce
-
Hi John
No I've got that what I'm struggling to understand is if you set the end float on the nut as the manual says then what are the shims for there's 16 of them in total?
Cheers
Bruce
-
Sorry that doesn't help the TR4 has a different trunnion (it's got a spindle through it) and doesn't have the dished washer
-
Hi All
I'm reassembling the front suspension on my TR4, I've fitted the trunnion and now I've got the thrust washers and lock washers to fit to the outer part of the trunnion/wishbone I've also got a large bag of shims. Can someone explain what I should be aiming for, should there be movement here ie should the thrust washer be able spin or is the whole thing supposed to be packed tight using the shims?
Thanks
Bruce
-
Hi Barry
Thanks for the photo that probably gives me what I need as I didn't really know what the lower bit looked like I've got a height from what was left on the car but any idea on the approximate width from bulkhead to edge? Sadly I've already fitted the repro battery tray and all of you are correct it's a bloody awful panel.
Cheers
Bruce
-
Hi All
I'm going to need to fabricate the two battery brackets on the bulkhead, my car came with a big hole where they used to be and unless I'm missing something no one makes them.
Anyone fancy posting close up photo's, dimensions etc any info gratefully received.
Cheers
Bruce
-
-
Hi all
I'm painting a stripped chassis/suspension with POR 15 rust preventative paint. The info says it discolours/ degrades in sunlight if you don't top coat. But as it's the chassis is there any point in top coating as it's unlikely to get much sunlight? Any opinions from those who have used it please.
Cheers
Bruce
-
Thanks Chaps I did try it with the wings fitted and the trim in place and it was still too high, but good spot with the seam weld stuart someone has indeed been there before me so i think I'll start by unpicking that and see where it gets me.
-
So I've been trying to get the bonnet gaps right on the car the bonnet isn't the original it looks like a later one from a TR 250 and its proud by about half an inch down the length of the near side. I've tried the various adjustments to no avail and also a large rubber mallet which was equally fruitless. The difference appears to be with the frame it sits flush on the offside but not on the near side(see photo's). Firstly am I being overly fussy about it and if not what do I do about it, source another bonnet? which looks like a very expensive option, or attempt to cut and weld the frame in order to lose the gap on the near side?
-
Thankyou gentlemen much appreciated
-
Hi all
Anyone got a recommendation for Blasting and Powder coating in Herts or North London? I've got a couple of rusty seat frames that need a birthday.
Cheers
Bruce
-
Thanks Alfred much appreciated
-
Hi
I'm in the process of converting a Lhd TR4 to Rhd and was hoping someone could tell me what the difference is between a TR4 dash and a TR4a dash backing are they essentially the same part and if not can the TR4a part be modified to do the job?
Cheers
Bruce
TR4 Grills & Rear Deck Peices - What do you think?
in TR4/4A Forum
Posted
Hi Rich
What was the verdict from the masses at Stonleigh and have you still got them or are you getting any more done? I currently have two slightly scruffy rear deck sets I'm not that enthusiastic about, but I'm even less enthusiatic about paying £300 for a new set I'm pretty sure wont fit very well.
Cheers
Bruce