PeterBosma Posted May 13 Report Share Posted May 13 I recently noticed a problem with my headlights. When I use the flasher stick, or press the high beam on the floor, the left light goes out, the right light works fine. I thought it was a faultly H4, so I put a new one in, same problem. What can it be? a fuse? realy? Quote Link to post Share on other sites
bob-menhennett Posted May 13 Report Share Posted May 13 (edited) Peter The first thing to eliminate is the connection on the dipswitch to the headlights , is that still attached. Not unheard of for the lucar connector parting company. You're looking for the Blue / White coloured wire. If it's not that follow the line to the Headlight relay , again looking for a disconnected or damaged wire to the nearside headlight. Then the back of the headlight it self , unusual but peel back the rubber boot if necessary to check. Sorry re thought. If it's just the one headlight then check the Headlight relay output to the nearside head light. terminal marking should be No 87. Shortly after the wires split , left and right at a rubber connector. Remove the wire and clean the bullet , replace and check lights. Bob Edited May 13 by bob-menhennett error Quote Link to post Share on other sites
RogerH Posted May 13 Report Share Posted May 13 Hi Peter, welcome to the Forum The flasher switch arrangement changed after '72 but there are similarities. See here for the wiring Typical wiring There is a fuse for the flasher switch- check this. BUT it does not control the foot switch. Using a Meter or bulb ion a fly lead - turn the main beam on and check at all the wiring connectors starting at the bulb ad working towards the switch. Actually undo the connectors and ensure they are clean (very clean) Roger Quote Link to post Share on other sites
RobH Posted May 13 Report Share Posted May 13 As standard there is no lighting relay so Bob's advice on that may not be relevant if your wiring has not been modified. This is the arrangement for a car with a foot dipswitch: As you can see both the LH and RH lamps are powered from the same switches and wires so if one works, the switches and power feed must be OK. A possible fault is in the connector where the LH and RH feeds are split, or in the connection to the RH lamp holder. Quote Link to post Share on other sites
PeterBosma Posted May 13 Author Report Share Posted May 13 (edited) ok, thank you all for the replies. I will do some research in the weekend, and will let you know if I can fix it. And perhaps to add to the symptom: when I engage the high beam, the low beam on the left lamp also quits working Edited May 13 by PeterBosma Quote Link to post Share on other sites
RobH Posted May 13 Report Share Posted May 13 18 minutes ago, PeterBosma said: And perhaps to add to the symptom: when I engage the high beam, the low beam on the left lamp also quits working I take it you mean that happens when you activate the headlamp flash Peter ? If so that is indeed odd. Quote Link to post Share on other sites
PeterBosma Posted May 13 Author Report Share Posted May 13 16 minutes ago, RobH said: I take it you mean that happens when you activate the headlamp flash Peter ? If so that is indeed odd. Indeed it does, when I activate the Highbeam with the foot or flash switch, the whole left lamp does not work, right lamp works fine. Or could it be that when you switch from low to high beam, the low beam does not burn at the same time? I thought that they both burned when you engage high beam? Quote Link to post Share on other sites
RobH Posted May 13 Report Share Posted May 13 No - you should have one or the other, not both except when you 'flash' when on low beam. Quote Link to post Share on other sites
stuart Posted May 13 Report Share Posted May 13 33 minutes ago, RobH said: No - you should have one or the other, not both except when you 'flash' when on low beam. Yes its only moderns with separate high/low lamps that have both on when using full beam. Stuart. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.