Jump to content

Recommended Posts

Hi All.

Just installing new wiring harness and bullets are very tight to get on and ever harder to separate. Somewhere in the distant memory banks I seem to recall reading the use of petroleum jelly on them. Is this 'Vaseline' and if so does it not cause a poor connection or is it conductive?

Any advice or alternatives welcome.

Many Thanks

Robert.

Link to post
Share on other sites

For connecting them, there is a tool:

image.png.957264f2d62edc428f9edadfed9cb1c8.png

Parting them, probably best to cut open the old femal part and get new, rather than pull on the wires!

But, yes, vaseline is, allegedly, conductive.

Link to post
Share on other sites

Hi Robert/John,

Petroleum Jelly and its derivatives are not conductive.

When you push the bullet connectors together tey scrap some of the jelly away and make metal to metal contact.

However it will keep moisture out of the connection and reduce corrosion.

 

Roger

Link to post
Share on other sites

Thnak you, Roger, I'll belive you rather than the online 'authorities'!

I fear that bullet connectors, a Lucas invention, are a major reaosn for the 'Prince of Darkness' reputation!

Link to post
Share on other sites

If you are going to put petroleum jelly on bullet connectors , do it AFTER the bullets have been inserted.  That way it doesn't interfere with achieving a good connection but will still help to stop moisture getting into the sleeve. 

Link to post
Share on other sites
8 hours ago, foster461 said:

I just push bullet connectors home with a small screwdriver, taking care to push the bullet not the solder or the wire. I have holes in my left hand as evidence.

I got fed up with making holes in my hand and bought a pair of the specialist pliers.  I agree, they are a bu88er to undo.

Rgds Ian

Link to post
Share on other sites
13 hours ago, john.r.davies said:

Mike, won't that risk short-circuiting the connectors, where they are double?

Double connectors are just that "Connectors" they are conjoined Unlike the separate connectors as used on older Jaguars etc.https://www.autosparks.co.uk/electrical-components/bullets-connector-sleeves/three-way-isolated-sleeve-connector

Stuart.

Link to post
Share on other sites

« I crimp the bullets rather than solder

This kit

https://www.autosparks.co.uk/electrical-components/wiring-tools/small-bullet-crimp-set-with-tools »

On the reccomendation of Mr Wigglesworth and in his words ‘feeling flush’ I bought this kit a few weeks ago, which, although they don’t give them away, makes life a lot easier. I have now got rid of all those awful ultra-modern blue connectors and under the bonnet there is now a period look of Lucas bullets and sleeves.

Next job, probably in the winter, is to reroute and tidy up all the wiring.

 

james

 

 

Link to post
Share on other sites

Hi James and other interested folk,

you must use the correct wire gauge for the bullet being crimped.

If the wire is too big then it will not fit in the bullet end hole (fail safe)

However if the wire is too slim then it will pull out after crimping. - always give it a reasonable tug after crimping.

 

Another oddity that I have found with the bullet connectors - there is space inside the bullet for the wire insulation to fit - but, the crimping tool does not crimp the body onto the insulation to give added strength.

 

Roger

Link to post
Share on other sites
3 hours ago, BlueTR3A-5EKT said:

 

This.  I started replacing the wiring harness without this gear.  The difference it makes and crimping the bullets makes it a breeze....if you exclude me trying to connect the right things together.

Edited by David Owen
Link to post
Share on other sites
1 hour ago, David Owen said:

 

This.  I started replacing the wiring harness without this gear.  The difference it makes and crimping the bullets makes it a breeze....if you exclude me trying to connect the right things together.

I removed all crimped connectors and replaced with soldered bullets. I think DIY crimping is not consistent enough and can lead to a resistance or open circuit , being difficult to find. As said Bullets can be difficult to undo after a time, and holes in hands are quite the norm!

Kevin

Link to post
Share on other sites
5 hours ago, stuart said:

Double connectors are just that "Connectors" they are conjoined Unlike the separate connectors as used on older Jaguars etc.https://www.autosparks.co.uk/electrical-components/bullets-connector-sleeves/three-way-isolated-sleeve-connector

Stuart.

That doesn't answer the question, Stuart!

Link to post
Share on other sites

I’ve mentioned my home made bullet press before, but in case anyone missed it here it is.

£1 Car boot pliers and a quarter of an hour with a cutting disk. A lot cheaper than the commercial ones.

 

CharlieBullitPress.thumb.jpg.0d89d40b5ddf929d763ab20959e80ceb.jpg

Link to post
Share on other sites
27 minutes ago, john.r.davies said:

That doesn't answer the question, Stuart!

Sorry I dont understand exactly what your on about in that case.

Stuart.

Link to post
Share on other sites
20 hours ago, john.r.davies said:

Mike, won't that risk short-circuiting the connectors, where they are double?

Hi John,

 there is some confusion here.

There are single bullet female connectors - one wire in/one wire out

There are also double bullet female connectors = two wires in/ two wires out - all four wires are shorted together.

 

I went another step further and removed the insulation from four double connectors . I then enclosed them in heat shrink.

If I did it again I would solder them together before the heatshrink.

 

Roger

Link to post
Share on other sites

Thank you, Roger!    I was referring to the separated female bullet connectors.     To smear a conducting grease on them would seem to risk a short circuit!

That's what I was asking, Stuart!

John

Link to post
Share on other sites
34 minutes ago, john.r.davies said:

Thank you, Roger!    I was referring to the separated female bullet connectors.     To smear a conducting grease on them would seem to risk a short circuit!

That's what I was asking, Stuart!

John

Hi John,

 the conductive grease is inside the connector - it can't touch others.

 

Hi Pete,

mine are bigger -  8 in/8 out

 

Roger

Link to post
Share on other sites

Of course the answer is there is really no need to use conductive grease. Fit them dry and if you wish, back fill with petroleum jelly.  ( I don't bother as I don't consider it necessary. After all, you don't grease spade connectors do you?)

In terms of pliers, an old pair of wire-strippers ground down is ideal:

pliers.jpg.9498d3d0309736496f1fb1551db77104.jpg

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

Please familiarise yourself with our Terms and Conditions. By using this site, you agree to the following: Terms of Use.