Rodbr Posted May 3, 2020 Report Share Posted May 3, 2020 Has anyone used these as they look to be useful as you can hold the item cure it and it is set without having to block into position or clamp it. I think this was developed from the dentistry business. interested in any experiences good or bad. Rod Quote Link to post Share on other sites
RogerH Posted May 3, 2020 Report Share Posted May 3, 2020 This was one of the first DIY ones available Roger Quote Link to post Share on other sites
Rodbr Posted May 3, 2020 Author Report Share Posted May 3, 2020 Hi Roger, Looks like it could be good for repairing e.g, cracking bakelite steering wheel,switch pulls , and paint the repair afterwards. I can see many potential applications in place of more conventional glues and the like. Rod. Quote Link to post Share on other sites
stuart Posted May 4, 2020 Report Share Posted May 4, 2020 Steering wheels are better repaired by "V" out the crack and then fill with a good epoxy filler then they can be rubbed down and refinished as normal. Stuart. Quote Link to post Share on other sites
MikeF Posted May 10, 2020 Report Share Posted May 10, 2020 Watched the video. The stuff dentists use is a development originally by ICI from the UV using blue light. Quite a technical achievement as there is much less energy available to kick the cure off. The implication that the demo glue in the video demonstration is the same grade/performance as a dental product needs to be verified, it's unlikely. . I can see the attraction of the delayed till started rapid cure, but conventional cyanoacrylates are pretty fast. You can speed them up even more by wiping the surfaces to be bonded with an accelerator. YOu can buy this or just use alcohol (Meths, surgical spirit, IPA,) Or even just huff on the work (as in cleaning your glasses). Some (cheaper) brands might give a white bond line. Of course the cure starts immediately on application. For anything structural I would be patient and stick with epoxies. (boom boom). They give relatively high bond strengths, are durable, resistant to moisture and most chemicals in a wide temperature operating range. Quote Link to post Share on other sites
AlanT Posted May 10, 2020 Report Share Posted May 10, 2020 Long been in use for repairs to circuit-boards. If you replace a track with a thin wire, because of damage or defect, you secure the wire with something very like this. It's usually green. You can deposit really tiny amounts between the pads and solder a chip down using hot air after its been cured. But you are right about epoxy. My wife chipped the rim of her favourite mug. Piece about 6mm diameter. Fine China mug. So I glued it back with Araldite not expecting it to last long. Been in daily use for TWENTY years. Quote Link to post Share on other sites
tthomson Posted May 10, 2020 Report Share Posted May 10, 2020 The main problem with UV cured glues is getting the light where you need it. For anything not transparent to UV light, you only cure the visible line, which can lead to later failure. I have used Araldite and other twin tube epoxies for repairing loads of things to great effect. If you want to increase the strength further embed carbon fibre in the epoxy. Quote Link to post Share on other sites
Tim D. Posted May 11, 2020 Report Share Posted May 11, 2020 Standard glue for repairing surf boards. Guess because they get plenty of access to sun. Quote Link to post Share on other sites
MikeF Posted May 11, 2020 Report Share Posted May 11, 2020 …………….For anything not transparent to UV light, you only cure the visible line,...………... Standard glue for repairing surf boards. Guess because they get plenty of access to sun --------------------- Some products will cure completely once initiated, speed of this later cure dependent on temperature Mike Quote Link to post Share on other sites
Andy Moltu Posted May 11, 2020 Report Share Posted May 11, 2020 Wasn’t it what they used to stick rear view mirrors in the Fords and other cars of the of XR3 era? Quote Link to post Share on other sites
Ian Vincent Posted May 11, 2020 Report Share Posted May 11, 2020 it's also the technology used in some windscreen chip repair kits. Rgds Ian Quote Link to post Share on other sites
stillp Posted May 12, 2020 Report Share Posted May 12, 2020 (edited) The stuff my dentist used to use for white fillings seems pretty good. The UV-cured outer layer acts as a catalyst so the rest cures almost instantly. OTOH I bought some cheap UV-cure superglue from China, which cures, but has zero bond strength. Pete Edited May 12, 2020 by stillp Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.