Dave McDonald Posted October 2, 2019 Report Share Posted October 2, 2019 The central H frame that I will be recovering for my TR5 restoration is fairly tatty. I will be putting a new cover on it but am reluctant to pull off the old split vinyl for fear of pulling off what appears to be an underlying foam/expanded polystyrene type padding. However, I don't want to put the new cover on and find that the blemishes, missing chunks, etc. in the old cover show through in the form of dips and bumps. I seem to remember a previous thread on the Forum about a product to fill these dips and cracks but can't remember when and where. Can anyone help please? Dave McD Quote Link to post Share on other sites
stuart Posted October 3, 2019 Report Share Posted October 3, 2019 If they are still available go for the TR. shop cover that has all the foam in it, you start with a bare ally frame, not cheap but very nice. Stuart. Quote Link to post Share on other sites
Dave McDonald Posted October 5, 2019 Author Report Share Posted October 5, 2019 On 10/3/2019 at 9:38 AM, stuart said: If they are still available go for the TR. shop cover that has all the foam in it, you start with a bare ally frame, not cheap but very nice. Stuart. Stuart, Thanks but I've already bought the new cover in a specific colour without foam. Is the padding simply that - a foam sponge layer? If so I have some thin foam which I could use glued on and strip the alloy bare first. Having trial fitted the H frame before stripping the dash with the new cover over the old covered frame it's VERY tight so I think I'll have to strip back to the bare frame and start with a new thin foam anyway. Dave McD Quote Link to post Share on other sites
Waldi Posted October 6, 2019 Report Share Posted October 6, 2019 Dave, I had a new vinyl cover without foam, it came with the car when I bought it; removed all existing foam, installed new foam, 3- 5 mm or so, and then glued the new cover on; I used a set of small clamps, 10 or so, and did a small section every day. It looks ok-ish but not perfect. This may be due to my limited trimming skills, but also, in some area’s, there was just not enough material. If you can repair the existing foam, I would try that first. If I had to buy a new cover it would certainly be a moulded cover. Regards, Waldi Quote Link to post Share on other sites
stuart Posted October 7, 2019 Report Share Posted October 7, 2019 On 10/5/2019 at 10:07 PM, Dave McDonald said: Stuart, Thanks but I've already bought the new cover in a specific colour without foam. Is the padding simply that - a foam sponge layer? If so I have some thin foam which I could use glued on and strip the alloy bare first. Having trial fitted the H frame before stripping the dash with the new cover over the old covered frame it's VERY tight so I think I'll have to strip back to the bare frame and start with a new thin foam anyway. Dave McD The foam in the new covers is essentially the same as original which is quite a solid foam injection moulded. Stuart. Quote Link to post Share on other sites
ntc Posted October 7, 2019 Report Share Posted October 7, 2019 You can repair the old one with Febfoam and trim to fit. Quote Link to post Share on other sites
Dave McDonald Posted October 7, 2019 Author Report Share Posted October 7, 2019 Thanks Neil. If you look at my first post, I asked what the product was to fill dips and cracks. I never thought of that type of expanding foam. Dave Quote Link to post Share on other sites
Mark69 Posted October 7, 2019 Report Share Posted October 7, 2019 (edited) For what it’s worth I recovered mine with one of the leather kits available,used foam on the front section but glued cover directly to the legs and back section. Really pleased with the end results. One other thing to take into account the nibs which support the speaker panels are part of the moulded cover and not the alloy frame Edited April 14, 2020 by Mark69 Quote Link to post Share on other sites
Waldi Posted October 8, 2019 Report Share Posted October 8, 2019 That looks very nice Mark, you are a better trimmer than me:) I think your method of not putting foam on the legs and back is better, and will give a tighter appearce than with the soft foam that I used all around. Cheers, Waldi Quote Link to post Share on other sites
SeanF Posted October 8, 2019 Report Share Posted October 8, 2019 I re-covered mine using foam from a wheel arch trimming kit. I had some spare since one of the big suppliers persuaded me that I needed to buy the foam separately but it also came with the Skinner trim set. I glued the foam on first then the vinyl covering. Very pleased with the result Quote Link to post Share on other sites
Dave McDonald Posted October 8, 2019 Author Report Share Posted October 8, 2019 Thanks, I've also got some spare foam sponge of the type that goes under the wheel arch trim so I've got different options now. Dave McD Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.