Jump to content

Problem fitting 4 seasons heater valve


Recommended Posts

As the title says i had a problem fitting the four seasons heater valve, the old one came out with no issue, I fitted the new one with some thread sealant even the rubber pipe went back on just fine, But I wasn't sure how tight to do it up, and so as the thread sealant says you can reposition up to four hours I thought I'll tighten it some more to be sure, that's when I noticed the valve would no longer turn with the lever!

 

I took it off again and I can't see where I've bent or pinched the housing, but it didn't take a lot for the top part to start spinning instead of the valve inside, so it's had it.

 

If i get another one, how do I put it back on? How tight is enough? Would the thread sealant (permatex) have held if had I just left it the 72 hours of curing time the first time?

 

Cheers

 

Gareth

Link to post
Share on other sites
  • Replies 85
  • Created
  • Last Reply

Top Posters In This Topic

When fitting them I usually just tighten down with some liquid PTFE until they are in the correct position using a spanner on the hex portion and when its reasonably tight and lined up then that will be fine. I have fitted quite a few with no problem and I would have thought the thread would give up before any other distortion would occur.if over tightened.

Stuart.

Link to post
Share on other sites

When fitting them I usually just tighten down with some liquid PTFE until they are in the correct position using a spanner on the hex portion and when its reasonably tight and lined up then that will be fine. I have fitted quite a few with no problem and I would have thought the thread would give up before any other distortion would occur.if over tightened.

Stuart.

Thanks Stuart, I'm not sure why it's locked up but I think the final turn was pretty tight and maybe distorted the body of it, I'll do it again and not over do it next time!

 

Can anyone please tell me what a 'Four Seasons' heater valve is???

 

Tom.

Hi Tom, it's an American brand heater valve that's pretty much a drop in fit for the original type

post-15576-0-96294100-1531760640_thumb.jpg

Link to post
Share on other sites

....and where I can get one as I live in the UK

 

 

(Its apparently far better than the Triumph item in terms of quality and life)

Edited by jogger321
Link to post
Share on other sites

....and where I can get one as I live in the UK

 

 

(Its apparently far better than the Triumph item in terms of quality and life)

 

I got mine from Amazon.com, They work out the import duty etc, comes to around £34 https://www.amazon.com/gp/product/B000C2UVQ4/ref=od_aui_detailpages00?ie=UTF8&psc=1

 

I think I've found out how I broke mine, there is a weld on the hex portion and i was using the wrong tool, a self tightening wrench, which i think pinched the very lower edge by pressing the weld inwards, I'll be using the correct spanner next time!

Link to post
Share on other sites

Brilliant thanks...Been after one for a while ...Just ordered one from Amazon

 

Whats the best way of fitting the cable at the heater valve end on these ?

Link to post
Share on other sites

Brilliant thanks...Been after one for a while ...Just ordered one from Amazon

 

Whats the best way of fitting the cable at the heater valve end on these ?

Two simple ways, either bend a hook in the current cable or crimp/solder an electrical eyelet on the end.

Link to post
Share on other sites

Hi

 

What is the gains by putting this in? Sorry for ignorance...

 

Rich

Supposed to be more reliable, and works better (the valve opens and closes easier)

Link to post
Share on other sites

1. a lot more reliable, 2. gives a proper unrestricted flow to the heater, 3. much easier to operate.

Stuart.

Link to post
Share on other sites

 

Whats the best way of fitting the cable at the heater valve end on these ?

A little stub of metal rod and some drill press time will yield a very neat solution.

 

Ed

post-12543-0-16241200-1531834811_thumb.jpg

Link to post
Share on other sites

A little stub of metal rod and some drill press time will yield a very neat solution.

Ed

That is neat Ed, how much are you selling those for !

 

Steve

Link to post
Share on other sites

...how much are you selling those for !

Steve

Well, when I finish the car, I might have time to make a batch. Til then, they are a pretty simple DIY project.

 

Ed

Link to post
Share on other sites

Some very clever people around :-)

 

+ 1

Link to post
Share on other sites

but I see no reason to change the original construction now,

it works without any problem since years,

I'll keep that in my mind

 

 

.

Edited by Z320
Link to post
Share on other sites

but I see no reason to change the original construction now,

it works without any problem since years,

I'll keep that in my mind

 

 

.

It is just a question of when, not if, the rubber diaphragm will fail. Usually in October when you turn the heater on for the first time.

 

Stan

Link to post
Share on other sites

Hi Stan,

 

when I have to change I will fit the american valve,

until this I will hold my eyes open on every cassic car market.

I do not want to go to the customs if not absolutely necessary.

That costs me always 2 h at all.

 

Ciao Marco

Link to post
Share on other sites

Brilliant thanks...Been after one for a while ...Just ordered one from Amazon

 

Whats the best way of fitting the cable at the heater valve end on these ?

How did you get Amazon to do this. They don't appear to ship to the UK.

 

Daz

Link to post
Share on other sites

How did you get Amazon to do this. They don't appear to ship to the UK.

Daz

I just logged in with my account on the.com site and it did it all for me

Link to post
Share on other sites

I just logged in with my account on the.com site and it did it all for me

 

Done that but once the item is in the cart it won't recognise its for international delivery.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...

Important Information

Please familiarise yourself with our Terms and Conditions. By using this site, you agree to the following: Terms of Use.