julie09 Posted October 19, 2017 Report Share Posted October 19, 2017 any tips on how to polish and keep polished chrome wire wheels after a through cleaning. could you use a spray polish used on furniture. Quote Link to post Share on other sites
RogerH Posted October 19, 2017 Report Share Posted October 19, 2017 Hi Julie, wire wheels are a time consuming item to keep clean. The way I did it was to use a long length of muslin cloth. Apply the polish with this cloth. I would thread it through/around the spokes and pull either end in turn and move up/down the spoke. Attack all the spokes and the centre hub. Using another clean length of cloth do the same process and remove the polish. Lock the car in the garage and don;t take it out. Roger Quote Link to post Share on other sites
TR5tar Posted October 19, 2017 Report Share Posted October 19, 2017 Hi Julie, Chrome wire wheels can be a pain to clean and keep clean, unless you enjoy spending lots of time on such things. When I go to town on the wheels, which only happens once a year at best, I remove them from the car, then use a degreaser to get the worst of the grime off, then use a brush and soapy water, then jet wash, then use a smaller brush and a chrome wire wheel cleaning product from one of the usual suppliers (make sure you get the one specifically for chrome wheels), to get into the more difficult areas. After that, I jet wash again and then use Autosol and a cloth to add shine. As Roger says, only way to then keep them clean is to not take the car out. One thing I occasionally do is smear a thin coat of vaseline over the chrome. It doesn't keep it clean, but perhaps it makes it a little easier to clean the next time. I don't know if it's worth it or not to be honest. Cheers, Darren Quote Link to post Share on other sites
rhino_mac Posted October 19, 2017 Report Share Posted October 19, 2017 Get ready to have aching fingers working to get behind the spokes. Chrome wheels are a nightmare to keep clean but they do look nice. I tend to find that as long as you clean them regularly, you can avoid polishing them (the spokes are stainless anyway) and wipe the brake dust away. Some polish on the rims and particularly the inside of the wheel (the back of the wheel) helps but I find Autoglym a bit harsh. There is a product recommended to me - I think it was this one (I'm at work and the bottle looks right). It has a wax in it that protects the chrome afterwards: http://www.thepolishingshop.co.uk/acatalog/Belgom.html Quote Link to post Share on other sites
RogerH Posted October 19, 2017 Report Share Posted October 19, 2017 Hi Richard, the wax in the Belgum helps to slow down the Ali oxidising. Not required on Chrome. You should not use an abrasive polish on chrome as it will wear away eventually. I was recommended to use Windowlene - good cleaner and no abrasive. Roger Quote Link to post Share on other sites
harlequin Posted October 19, 2017 Report Share Posted October 19, 2017 Tr shop wire wheel cleaner and finish works a treat. I do mine twice a year takes about an hour George Quote Link to post Share on other sites
pfenlon Posted October 19, 2017 Report Share Posted October 19, 2017 (edited) Where is Peter Dykins when you need him? Polishing his TR with a "V" in the middle no doubt. Edited October 19, 2017 by pfenlon Quote Link to post Share on other sites
Alec Pringle Posted October 19, 2017 Report Share Posted October 19, 2017 PTFE spray, Teflon 'dry lubricant', is good for sealing the chrome and helping to keep corrosion at bay . . . . . Cheers, Alec Quote Link to post Share on other sites
Dave Larnder Posted October 20, 2017 Report Share Posted October 20, 2017 Julie I only use elbow grease! It takes 1.5 hours per wheel to do on a jig I have mounted on the bench, so I can sit down to do the work. It is particularly easy to clean the inside of the rim etc. by turning the jig around, and use a damp cloth first off, followed by a dry one. I use a strip of cotton cloth about 18" long x 6" wide that I wrap around each spoke and the pull on the ends about 6 times each before sliding up the spokes. I have just come home from Switzerland and 2330 miles of sometimes wet weather so they are good and dirty, so I only do one wheel a day as it makes your fingers ache something awful. When they are done it is worth the effort, and I do get frequently asked hoe do I get them so clean as they glint I the sun when moving off. I recently repainted the rear brake drums silver instead of black and I think it makes them look even better. Dave Quote Link to post Share on other sites
Andrew Smith Posted October 20, 2017 Report Share Posted October 20, 2017 Bimey, you lot do it the hard way - all you need is the MWS cleaning kit; two bottles of solution (cleaner and polisher) and a soft brush then either wipe yo a shine or air dry - all done in about 60 - 90 minutes! Cheers Andrew Quote Link to post Share on other sites
TR4ffic Posted October 20, 2017 Report Share Posted October 20, 2017 Bimey, you lot do it the hard way - all you need is the MWS cleaning kit; two bottles of solution (cleaner and polisher) and a soft brush then either wipe yo a shine or air dry - all done in about 60 - 90 minutes! Cheers Andrew +1 Take the wheel off - 15 mins per wheel tops.. Simples... Quote Link to post Share on other sites
Dave Larnder Posted October 21, 2017 Report Share Posted October 21, 2017 Andrew Surely with your method you still have water marks on the rim, hub and possibly the spokes. TR4ffic Not if they are done properly.(spotless) Dave Quote Link to post Share on other sites
TR4ffic Posted October 21, 2017 Report Share Posted October 21, 2017 TR4ffic Not if they are done properly.(spotless) Ohh - I beg to differ... The MWS Cleaning Kit works a treat and they do come up spotless and bright... They were new in March, though On my 4a with chrome wires, I went down the... ...use elbow grease! It takes 1.5 hours per wheel... ...route. What a faff..! Quote Link to post Share on other sites
Andrew Smith Posted October 21, 2017 Report Share Posted October 21, 2017 Surely with your method you still have water marks on the rim, hub and possibly the spokes. No Dave, a quick wipe with a microfiber cloth and they're all sparkly again. Cheers Andrew Quote Link to post Share on other sites
julie09 Posted October 22, 2017 Author Report Share Posted October 22, 2017 Thanks for all your suggestions. With the PTFE spray does it dry so that dust does not stick and where do I buy PTFE spray and MWS cleaner. I will give anything a try. Quote Link to post Share on other sites
Andrew Smith Posted October 22, 2017 Report Share Posted October 22, 2017 Thanks for all your suggestions. With the PTFE spray does it dry so that dust does not stick and where do I buy PTFE spray and MWS cleaner. I will give anything a try. Here you go - http://www.moss-europe.co.uk/wire-wheel-cleaning-kit-gac4134x.html Quote Link to post Share on other sites
Alec Pringle Posted October 22, 2017 Report Share Posted October 22, 2017 PTFE is also known as Teflon, non-stick stuff, it's a dry lubricant . . . . . Ebay is your friend here, just search for PTFE spray, and it's also used a lot by the bicycling fraternity . . . . . every bike shop will have a decent version. Cheers Alec Quote Link to post Share on other sites
TR5tar Posted October 22, 2017 Report Share Posted October 22, 2017 Hi Julie, I think Alec's suggestion of PTFE spray relates specifically to protecting the chrome from corrosion. I occasionally use vaseline for this purpose, but Alec's suggestion is better I think. However, I'm not sure that it would stop dust from settling on the wheels or dirt attaching. Halfords stock PTFE spray and it can also be found from online suppliers. With wire wheels it's always going to be a job to keep them clean. If you are not keen on that, how about getting some steel wheels for winter and then just using the wires when the weather is good. Cheers, Darren Quote Link to post Share on other sites
Ian Vincent Posted October 22, 2017 Report Share Posted October 22, 2017 Or have painted wires. Rgds Ian Quote Link to post Share on other sites
Fireman049 Posted October 22, 2017 Report Share Posted October 22, 2017 (edited) Where can you get steel wheels with centre lock attachments??? Tom. Edited October 22, 2017 by Fireman049 Quote Link to post Share on other sites
Dave Larnder Posted October 22, 2017 Report Share Posted October 22, 2017 Where can you get steel wheels with centre lock attachments??? Tom. Tom My question exactly. Dave Quote Link to post Share on other sites
stuart Posted October 23, 2017 Report Share Posted October 23, 2017 Where can you get steel wheels with centre lock attachments??? Tom. I thought you already had them Tom? Stuart. Quote Link to post Share on other sites
Fireman049 Posted October 23, 2017 Report Share Posted October 23, 2017 Hi Stuart ~ My wheels are Dunlop alloy. Tom. Quote Link to post Share on other sites
james christie Posted October 23, 2017 Report Share Posted October 23, 2017 Where d'ya get them ,Tom. I too have lost my patience and motivation to clean my wire wheels. Must be an age thing..... James Quote Link to post Share on other sites
Fireman049 Posted October 23, 2017 Report Share Posted October 23, 2017 Hi James ~ You have a PM from me. Tom. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.