pinky Posted August 14, 2017 Report Share Posted August 14, 2017 hi my friends, I noted the other day that drivers side rear wheel was sticking out more than the near side the car drives fine. I stript it down to see if there were elongated holes, or something was broken, nothing, scratched my head a couple of times, (got a splinter) I now believe the body has moved, has this happened to any one else cheers pink , Quote Link to post Share on other sites
RogerH Posted August 14, 2017 Report Share Posted August 14, 2017 Hi Pinky, they do not generally move unless something big happens. But they can be put on on the P*ss. How far out is it.? Roger Quote Link to post Share on other sites
pinky Posted August 14, 2017 Author Report Share Posted August 14, 2017 Well it did have a knock on the bumper, a couple of months ago a lotus reversed into the bumper total wiped out the fibreglass bumper, didn't scratch the triumph, however did it move the body, the drivers side wheel sticks out 3/4 of an inch further than the near side pink Quote Link to post Share on other sites
RogerH Posted August 14, 2017 Report Share Posted August 14, 2017 That may have done it. Roger Quote Link to post Share on other sites
Jersey Royal Posted August 14, 2017 Report Share Posted August 14, 2017 (edited) Pink, I can tell you that your rear wheel,has been sticking out like that since the last time I saw your motor at IWE, so that's three years. About the time you fitted the larger wheels which have made the error appear even bigger. Cheers Guy Ps Ask Stuart....Neil, or half of the people who attended the last proper forum meet at IWE. Edited August 14, 2017 by Jersey Royal Quote Link to post Share on other sites
Guest ntc Posted August 14, 2017 Report Share Posted August 14, 2017 Confirm Pink that is correct,you could see it then. Quote Link to post Share on other sites
pinky Posted August 14, 2017 Author Report Share Posted August 14, 2017 Nice to see you back on the forum guy, I have noted your observations of past times, I now must find the error and put it right pink Quote Link to post Share on other sites
Guest ntc Posted August 14, 2017 Report Share Posted August 14, 2017 Pink The big wheels did show it,and you would be suprised how many are the same look hard to find it. Quote Link to post Share on other sites
Jersey Royal Posted August 14, 2017 Report Share Posted August 14, 2017 (edited) Nice to see you back on the forum guy, I have noted your observations of past times, I now must find the error and put it right pink Pink, Do you recall Carl doing the four wheel alignment on your Tr. I think that's when it appeared I think you should check the chassis for straightness, drop a few string lines onto the garage floor, easy for you as you have a pit. So tape some cardboard to floor and plumb down the main rails, trailing arms etc. Then go from there As the car is now the wheels are in alignment . Only trying to be helpful mi old fruit.And not back on the forum. Cheers Guy Edited August 14, 2017 by Jersey Royal Quote Link to post Share on other sites
foster461 Posted August 15, 2017 Report Share Posted August 15, 2017 Guy, I hope you are doing well. Pink, it would take a really hard hit to move the body on the frame even if all of the bolts were less than tight. If it was hit that hard the body would likely crumple at the location it was hit before it would move on the frame. The car may have been like that from birth and the bigger tires just exaggerate it. Stan Quote Link to post Share on other sites
Tonymolloy Posted August 17, 2017 Report Share Posted August 17, 2017 My tr6 has one of the rear wheels sticking out further on one side,in fact it leans outwards,I'm just having it sorted at the moment at kd triumph in Coventry ,I'm having all the rear end re- bushed with super flex bushes,looking at the old bushes in the trailing arms they didn't seem to be sitting square,so hopefully they should be ok when all re- fitted. Quote Link to post Share on other sites
Matt Posted April 12, 2021 Report Share Posted April 12, 2021 (edited) Sorry to dig up an old post. I've just looked at TR that has this very issue, is it easy to fix or is one of those the more you dig the more you find? Thanks in advance, Matt Edited April 12, 2021 by Matt Quote Link to post Share on other sites
stuart Posted April 13, 2021 Report Share Posted April 13, 2021 13 hours ago, Matt said: Sorry to dig up an old post. I've just looked at TR that has this very issue, is it easy to fix or is one of those the more you dig the more you find? Thanks in advance, Matt It can happen for a number of reasons so you do need to have a real good look underneath and take a tape measure with you, it will become apparent what the problem is if you measure to different points side to side. Stuart. Quote Link to post Share on other sites
Matt Posted April 13, 2021 Report Share Posted April 13, 2021 Hi Stuart, Thanks for the taking the time to reply. I didn't have a tape measure to hand but you could feel the difference in the gap between the training arms and the body, I should have looked deeper to see if it was just the arms or the chassis to body. I've not been under a TR for a while and just thinking about it I would be surprised if you could move the trailing arms 1/4 inch left or right, is that possible or would it be the chassis to body fit? Thanks again, Matt Quote Link to post Share on other sites
stuart Posted April 13, 2021 Report Share Posted April 13, 2021 It could be either the body is over a bit, badly done floor/sill repairs or and its an odd one the trailing arm sections in the chassis have been replaced, many years ago the only repair sections for that area didnt have the holes drilled for the mountings so it was possible to fit the trailing arms a bit out from where they should be, there`s enough range of movement on the sliding joints to accommodate this. This is why I said about a tape measure being useful to check where the problem comes from. Stuart. Quote Link to post Share on other sites
Matt Posted April 13, 2021 Report Share Posted April 13, 2021 Stuart, As always thanks for your input, I’m planning on heading back to get a proper look at the weekend I’ll let you know what I find. Matt Quote Link to post Share on other sites
ntc Posted April 13, 2021 Report Share Posted April 13, 2021 Matt Look at the rear of the car how much of the chassis can you see below the rear apron and are they the same? Also look at the camber angle on both wheels they should also be the same Quote Link to post Share on other sites
stuart Posted April 14, 2021 Report Share Posted April 14, 2021 14 hours ago, ntc said: Matt Look at the rear of the car how much of the chassis can you see below the rear apron and are they the same? Also look at the camber angle on both wheels they should also be the same Like this Stuart. Quote Link to post Share on other sites
Matt Posted April 19, 2021 Report Share Posted April 19, 2021 Looked at the car again over the weekend, up in the air with a tape measure in hand. Chassis was 15mm nearer the offside sill but was very solid and no real sign of hogging or rust. The more disturbing part was the fact the top of the tyre could be seen on the nearside and the nearside trailing arm was 10mm closer to the sill than the offside. So tyre can be seen on the nearside but chassis is already 15mm closer to the offside. I’m guessing the chassis had been repaired at some point, errors made on where holes should be for the trailing arms and when the body was put back on they tried to counteract this by putting it on slightly askew and closer to the nearside. Thanks for the guidance. Matt Quote Link to post Share on other sites
stuart Posted April 20, 2021 Report Share Posted April 20, 2021 13 hours ago, Matt said: Looked at the car again over the weekend, up in the air with a tape measure in hand. Chassis was 15mm nearer the offside sill but was very solid and no real sign of hogging or rust. The more disturbing part was the fact the top of the tyre could be seen on the nearside and the nearside trailing arm was 10mm closer to the sill than the offside. So tyre can be seen on the nearside but chassis is already 15mm closer to the offside. I’m guessing the chassis had been repaired at some point, errors made on where holes should be for the trailing arms and when the body was put back on they tried to counteract this by putting it on slightly askew and closer to the nearside. Thanks for the guidance. Matt Seems like what I said earlier about holes in the trailing arm being put in in the wrong place. Stuart. Quote Link to post Share on other sites
bobmac Posted June 30, 2021 Report Share Posted June 30, 2021 I have seen various post in reference to rear wheel alignment and just experienced one of the many problems with alignment. Re-commissioning car, after being off road since 1989!, rebushed rear end but noted passenger side wheel turned inwards, no amount of shims or movement could align wheel correctly and maintain 88" length wheelbase , and rear wheel width 50.2" found to be over 1 1/2" to wide. After much head scratching I concluded problem was with drive shaft length luckily I had a spare shaft and on removing fitted shaft and checked against spare found fitted shaft was almost 2" longer, changed shaft and now have perfect dimensions on wheelbases. Having searched the forum an web the conclusion I have arrived at is that sometime in cars distant past somebody had fitted a drive shaft from a Triumph 2000! I advise above as a note to other members who may have similar problem. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.