Ian Vincent

+1

If I were using mine every day then I would want a 100 or even 200 litre tank but since I only use mine intermittently now, the 50 litre tank is fine and takes less time to come up to pressure when I turn it on. Rgds Ian

I can remember going to the motorshow at the NEC when the first SLK was released (1995?) and I recall it being Sportlich, Leicht, Kurz. We had an SLK280 for many years, in fact I only sold it when my wife died. The only issue we ever had was the gearbox selector plate had to be replaced when the car was about 10 years old. Rgds Ian

One reason is because the blue stuff is very toxic. And it’s not about spending a lot of time looking for an alternative, the alternative has been out there for a while. But in the end it comes down to personal choice, I went with Fernox and to date am happy with it. Rgds Ian

Very cunning with the two sticky pads. Rgds Ian

My 1959 TR3a has 14 around the body at the rear and four on each door. This aligns with all the info I had at the time of doing the original restoration back in 2010ish. Two of the body ones are low down alongside the ‘B’ post for the doors. One each side. Rgds Ian

FWIW, I have using Fernox Alpha for the last couple of years. Apart from being kinder to the environment (allegedly), it only has to be changed every 10 years. Rgds Ian

Maybe this the reason why I had a message this morning advising me to change a whole heap of passwords because they had been compromised through a data hack. Rgds Ian

A bit late in the day, but why is he buying/ has he bought a Defender? I recently bought a new (to me) SUV and I avoided Range Rover completely because of this issue of cloning. The only way to impact the manufacturer is through sales. If the public stops buying cars with keyless go, the manufacturers would be forced to come up with something more secure. Rgds Ian

Thank you all, plenty of food for thought there. Needless to say I won’t be buying the genuine item at $350 and I do like the rod although it does look a bit pricey. I’ll post how I get on in due course. Rgds Ian

Thks Iain.

I have pair of those already thks George but I wanted something period to fit at the top of the screen. Rgds Ian

I occasionally use a boot bag on my TR3a with result that it blocks the view from my dashboard mounted rear view mirror. I have often thought about fitting a mirror on a rod ‘a la’ e- type or MG. Has anyone on the forum done this and if so who supplies the best set of bits? Rgds Ian

I’m not sure about that Bob, my LED ones are pretty bright. The reflection back off road signs is just as bright if not brighter than the lights on my daily driver with HID lights. Rgds Ian

Without wishing to be a pedant, they could be flat but not perpendicular to the thread.

Nope, the one inside. But check all the things suggested by the others before you start removing the gearbox. Rgds Ian

I'd be worried that the pin in the clutch operating arm has sheared. Rgds Ian

Judging by the speeds the average white van man gets up to, I wouldn't be too worried about the speed rating. What do you use your TR for? Rgds Ian

I cleaned mine with a homemade soda blaster. It worked a treat. Rgds Ian

I set my torque wrench to 60 ft-lbs for the wire wheel extension nuts and use loctite as well, but I have had one come loose a long time ago. Very disconcerting plus it knackered the studs and I had the faff of replacing them. Rgds Ian

I bought something very similar to that from Lidl a couple of years ago. Cost me £7 I think, so maybe keep an eye out for when they have them again. Rgds Ian

The problem with the Gunsons Eze-bleed for me was getting a seal at the top of the fluid reservoir. The thread is not very well formed and it was very hit or miss and then the final time I tried to use it the cap actually blew off and sprayed the engine bay with brake fluid. It’s been on the shelf ever since and I’ve found a work around. Rgds Ian

Having had problems in the past with liner heights, when I rebuilt my engine, (coincidentally at about the same time as Bob did his), I entrusted the whole machining exercise to a reputed machine shop, (the same firm that does all the work for Revington) and for about £1,000 they sorted everything including decking the pistons, crack testing the crank and then giving it a re grind and balancing everything. Money well spent as far as I was concerned. They even cleaned everything and blew out the crank. All I had to do was put it back together. Rgds Ian

I agree it’s an issue but it’s naive to think that even in the unlikely event that the petition reaches the 100k threshold the Government is going to do anything about it. My solution has been to fit Classic Car LED bulbs so that I have the ability to see past the oncoming vehicles. Not really the right answer I know but one that recognises reality. Let’s face it, my current daily driver is an SUV with modern high intensity lights and I would be very pissed off if someone told me to downgrade them to something less effective. Rgds Ian

Good suggestion, I’ll give it a go tomorrow. Thanks. Rgds Ian