-
Content Count
790 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Posts posted by Graze
-
-
its been a while since I've been on here and having sold my TR6 2 years ago I have just sold my TR4 and am now without a Triumph for the first time in many years. As you can see the TR4 wasnt original but its a great car & gone to a new owner who will get lots of enjoyment from it
I'd like to thank the forum community for all the help they have given me over the years & all the enjoymentI've had from these great little cars
best wishes to you all
Graeme
-
So having rebuilt my TR4 (mostly Racestorations supplied parts) into a high out put fast road motor I was having all sorts of problems getting the car to run when warm. It was generating so much heat under the bonnet that fuel was vaporising in the fuel lines ( they were measured at 92deg C) as well as in the webers.
wrapping the extractors, sheathing the fuel lines, installing two layers of heat shield between the webers and the extractors and directing cold air to the trumpets and to the air space between the heat shields ( plus upgraded electronic ignition, rebuilt distributor) solved all this
Now runs like I'd always hoped
-
Thanks all
Graeme
-
I just want to double check recommended oil grades for my TR4
engine was re built 2years ago & I have been using Penrite 10W-50 extra zinc full mineral which I think is correct
just had the gearbox & J type overdrive re furbished - believe EP 90 GL4 is the correct oil but some people use the same as the engine as I understand - is the Penrite ok?
and for the diff - not been re built but still performing ok - what should i use?
and want to re-do the uprated lever arm dampers - what is the best oil grade for them?
any advice would be much appreciated
Graeme
-
Many thanks gents - as always helpful suggestions from the forum
yes Stuart is correct it is the actual latch / lock mounted on the end of the door not the barrel key lock that I need - these are sadly no longer available from the usual suspects
Roger - I will try the other suppliers you mention - thanks
Graeme
-
Hi,,
A plea to anyone who may be able to furnish me with a used (as I believe new are no longer available) door lock for drivers door on my 75 TR6
the original one has broken & locked the door shut - now managed to get it open (not easy)
I cannot buy a lock from Rimmer/ Moss etc as they no longer supply them
does anyone have a spare I could purchase
many thanks in advance
Graeme
-
many thanks Steve
-
Steve
photos would definitely assist thanks
Tom
I tried to unlock it via the lever attached to the external key lock but cant seem to get it to work. It may be worth more attention though as a possible solution
thanks guys
Graeme
-
Closed the door the other day & it has locked itself shut
the outside handle which pushes against the lever is not working as the lever is moving freely inside the door - appears to be broken & disconnected form the latch.
the inside handle is working and when pulled back appears to depress the lever into the latch but to no effect
I cant fully remove the door trim panel as the bottom corner is held in place by the B pillar diagonal brace but I can gain access to the dor cavity
does anyone have any suggestions on how to free the latch?
Graeme
-
Consider a direct connected cable to the solenoid through a switch from battery power that your passenger can operate when you run the car with the tunnel off - that should eliminate either the car electrical circuit fault or suggest an overdrive internal operation fault.
Consider dropping the filters out of the overdrive and cleaning them - they are behind the ribbed plate held on with 6 screws - item 47, You will probably need a gasket! see also 50, 55 here https://www.moss-europe.co.uk/shop-by-model/triumph/tr5-6/clutch-transmission-drivetrain/overdrives-components/j-type-overdrive-fittings-tr5-6.html
Cheers
Peter W
Thanks Peter, good suggestions
Graeme
-
thanks guys
will check out the switch (but it is only 1 year old and was working perfectly), will also take tunnel off & drive it to see if anything is visible
yes Mal relay fitted
Graeme
-
Update
have removed gearbox tunnel cover & checked all connections, have ensured no chance of screws from gear l;ever surround are touching gearbox, angle drive (which was added prior to issue arising) is clear of any contact with chassis etc
Ive tried to eliminate a number of potential electrical issues & checked all connections and dont think it is a short circuit
is there anything in the gearbox/overdrive that would be affected by oil with extra zinc additive in it as the 20W-50 is extra zinc
I'm at a bit of a loss as I think if its not electrical it must be as a result of the oil top up
help /advice appreciated
Graeme
-
Steve, Ian
Thanks for the replies
Took it on another Sunday drive today
Overdrive worked perfectly on flat motorway but on back roads which of course are bumpy was again intermittent
Leads me to electrical connections as my next check
Hopefully without needing to pull the tunnel Etc out
Many thanks
Graeme
-
My J type overdrive started intermittently phasing in & out on the last spirited drive
followed me discovering that the gearbox was low on oil
in the absence of anything else I had topped it up with full mineral 20W-60 (not sure what had been in there previously) prior to the long (300km) drive
It started on RH corners then was doing it regularly in all circumstances
I thought it may be oil related so today emptied the gearbox & re filled with Penrite 80W-90 Gear Oil (which Penrite recommend)
doesnt seem to have made any real difference - when not under load it holds the overdrive gearing but under acceleration drops back Out of overdrive
any suggestions?
could it be the solenoid playing up & no relation to the oil?
advice welcome
Graeme
-
I have a spare reasonable condition Tr4 one if you are interested (not sure if you have a TR4 or 4A
Graeme
-
ive got semi slick tyres - 205/50/15 on front & 225/50/15 on rear of my TR4
they work well, although a little small on overall diameter on rear make gearing a bit shorter
Graze
-
Stuart photo now attached to previous post
cooking dinner got in the way
entirely possible its a volvo unit - purchased from the US
Graeme
-
Interestingly Alan its a J type and has a bracket botled to the chassis which sits across under the back of the o'drive with a rubber mount and an L shaped bracket which is bolted to the back of the overdrive cover - all as its meant to be I'm sure
Also my cover has two bolt holes on the underside too -- but not used due to the bracket
Graze
-
Why is the rear housing fitted upside down?
Stuart.
Well that is a good question?
shortage of TR experts still alive here
thats the way I got it back from the guy who refurbed it & i didnt know any better
seems to work ok - is there any long term consequence requiring me to pull it all apart & re install (or do I just leave it till next time I need to pull it out?)
Graeme
-
thanks again Roger
should be able to sort it from there
Graeme
-
Roger
thanks for the advice & link to buckeye
removed, stripped, switch threads tapped into the cover - will have O'drive on 2nd, 3rd, 4th
cover painted & ready to re-install
It was a relatively easy job & I had lots of help from someone who knew what they were doing
next challenge will be the wiring to the switches
I know that i need to wire the two switches to each other & to ground off one side, then the column switch has two wires - yellow/ green to switches & then to solenoid?, where do I wre the other one to get the power?
where do i take the power from & connect it to - do i need a relay
J type overdrive
advice appreciated
Graze
-
Thanks Michael/Roger
Seems my 3rd/4th selector fork on the replacement is badly worn so I will need to pull the current one off the car and hopefully it will be in better shape and can be re-used
Graeme
-
Thanks Roger
Appreciated
Graze
-
I need some advice
I have to change the gearbox top cover on my newly fitted overdrive gearbox. Seems the original selector top cover from my gearbox had the switch location in the wrong spot (on the RH side opposite the reverse lights switch) meaning I had the luxury of overdrive on all 5 gears (reverse too if I had been silly enough to try it)
So never having pulled one of these off before is there any special tricks to removing the selector & forks & fitting the new one? Its being done in the car just to make it interesting!
all help appreciated
Graeme
Leaving Triumph Ownership - a thankyou!
in TR4/4A Forum
Posted
Mal
nothing at the moment
Since I was 20 I have been lucky enough to have an MGA, MGB, MGBGT, TR6, TR4 so probably all the old british sports cars I need
I have an F Type R now as a daily and a V12 Vantage S for giggles - both much more comfortable, but I must say the TR4 as it finished up with all the mods was a lot of fun at almost legal speeds - although it ended up costing me as much to build & repair over the years as the F Type (2nd hand) did to buy
Graeme